旋转活塞式灌装机适合容积灌装泵输送的物料。
ZB rotary piston fillers are suitable to fill volumetrically all pumpable products.
再旋转活塞杆使其缺口离开挡板就可继续进行抽吸。
The cylinder rod is rotated again to cause the nicks to leave the baffle to continue suction.
本发明公开了一种旋转活塞发动机,属于内燃机技术领域。
The invention discloses a rotary piston engine, pertaining to the technical field of internal combustion engines.
当被输送介质的粘度大于100厘泊时,可选用容积式旋转活塞泵。
When the viscosity of the medium being transferred is higher than 100cp, volumetric rotating piston pumps can be used.
介绍了用3B格式在数控线切割机床上加工等距型面旋转活塞的编程方法。
It introduces the programming method to cutting Revolving piston of equal distance plane on numerical control linear cutting machine by 3b format.
滑阀真空泵是一种容积式真空泵,在各工业领域广泛应用。但该泵的旋转活塞平衡长期以来无精确计算方法。
Rotary piston pump is a volume type vacuum pump and is applied widely, but there has been no method for exactly calculating dynamic balance of rotary piston up to the present.
介绍了苏尔寿ZA40S型柴油机所采用的的旋转活塞的运动机理及其独特的优点,并对该型机组在使用管理中需要注意的问题作了阐述。
This paper presents the mechanism and advantages of rotating pistons for Sulzer diesel engines ZA40S. and describes the problems to be pay attention to in maintenance and operation of the engines.
首先,旋转并拉出一个活塞,让硬盘滑出服务器的盒子。
First, a plunger is pulled and rotated to release the drive and allow it to slide out of the server's case.
这么高速的旋转相当于在活塞上施加9000倍的重力。
Revving at such massive speeds equates to an accelerative force on the pistons of nearly 9000 times gravity.
曲轴,也叫做发动机的“脊柱”,其作用是将活塞的上下往复运动转换成为旋转运动,并且控制着整个的功率输出。
The crankshaft, regarded as the "backbone" of the engine, serves to change the reciprocating motion of the piston into rotary motion and handles the entire power output.
触发叶轮随发动机转速而旋转,使得转速传感器或拾波线圈产生与发动机转速和活塞位置相对应的触发电压脉冲。
The trigger wheel rotates with engine RPMs and causes the speed sensor, or pickup oil, to produce triggering voltage pulses that correspond to engine speed and piston position.
循环泵将曲轴旋转运动转化为柱塞的直线运动。泵速转每分钟决定了任何气缸和活塞组合的排泵量。
Reciprocating pumps convert rotary motion to linear motion. Pump speed in RPM determines the pumps output volume for any given combination of cylinder bore and piston stroke.
往复式压缩机使用的是活塞、曲柄、连杆机构或活塞、曲柄、滑管机构,旋转式压缩机使用的是转轴曲轴机构。
Reciprocating compressors is using the piston, the crank, link mechanism or the piston, the crank, sliding tube institutions, rotary compressor rotor is the use of crankshaft institutions.
正如在其孔活塞杆,曲轴旋转,加压相反的孔反转旋转。
As the piston strokes in its bore, the crankshaft rotates, pressurizing the opposite bore reverses rotation.
那台机器由气缸、活塞、旋转轴、齿轮、轴承、螺栓、螺丝钉和不锈钢外壳组成。
The machine consists of cylinder, piston, rotary, shaft, gears, bearings, bolts, screws and stainless steel crusts.
两种主要的空压机类型为往复式(活塞式)和旋转式(螺杆式)。
Of the two main air compressor types for reciprocating (piston) and rotary (screw).
活塞通过连杆和轴连接,使得气体带动轴旋转半圈。
Linking the piston by a connecting rod to a crankshaft causes the gas to rotate the shaft through half a turn.
通过消除四个埋头螺丝保持精确一致,该活塞杆和模具板可旋转方向没有拆卸气缸90度。
By removing the four countersunk screws that maintain exact alignment, the orientation of the piston rods and tooling plate can be rotated 90 degrees without cylinder disassembly.
要生产泵动作用,它包括往复运动的活塞或旋转叶片。
To produce the pumping action, it contains pistons that are driven back and forth, or rotating vanes.
那连接竿送活塞的上上下下运动到机桥,将它换成旋转的运动。
The connecting rod transmits the up-and-down motion of the piston to the crankshaft, which changes it into rotary motion .
该泵使用一个共同的驱动机构以使活塞轴向旋转且沿侧向往复运动以连续地泵送流体,同时减少脉动。
The pump utilizes one common driving mechanism to axially rotate and laterally reciprocate the piston to provide continuous pumping of fluids with reduced pulsations.
在工作循环的第三个冲程开始,活塞再次位于上止点,曲轴已经旋转了一整周。
At the beginning of the third stroke of the cycle of operations, the piston is once again at TDC, the crankshaft having turned through one full revolution.
调整旋转双螺杆都涵盖和活塞队,以避免连续沉重压力的牙齿,竖井机构。
Twin adjust rotation screw on both covers and pistons, to avoid continuous heavy stresses by teeth, shaft, body.
介绍了三角活塞旋转发动机的工作原理,提出了气缸型线的创成方法和计算公式。
This paper introduces the operating principles of the triangle piston circulating engine and puts forward the methods to create model line of cylinder and calculating formula.
汽缸内多个汽缸容积由曲轴带动下旋转的活塞在汽缸容积的位置角度变化而不同。
The plurality of cylinder volumes in the cylinder are different according to the Angle change of the position of the piston rotating in the cylinder volumes under the drive of a crankshaft.
正如在其孔活塞杆,曲轴旋转。
八个活塞体来回内外运动,带动曲轴连续旋转,再通过多对锥齿轮相互啮合的方式,实现动力的输出。
The 8 piston bodies move to and fro, in and out, and drive the crankshaft to rotate continuously, then the power is output by the engagement of conic gears.
旋转止回阀活塞。当移动喷嘴时,用勺子或其它工具穿过狭缝以产生更大的杠杆力。
Turns Check Valve Plug. Use a spoon or other tool through slot for more leverage when removing Jet.
家轿后减振器活塞杆在进行旋转弯曲疲劳试验时出现早期断裂。
The piston rod of family sedan's rear snubber fractured duringearlier stage of rotary bending fatigue test.
家轿后减振器活塞杆在进行旋转弯曲疲劳试验时出现早期断裂。
The piston rod of family sedan's rear snubber fractured duringearlier stage of rotary bending fatigue test.
应用推荐