最简单的加载情况是周期地、均匀而重复地施加的载荷。
The simplest imposed conditions are those in which the loading is periodically and uniformly repeated.
因为这种扁平的配置，施加到电缆上的机械载荷分散在其总宽度上。
With this flat configuration, the mechanical load applied to the cable is distributed over the total width of the cable.
该方法以测量的应变值为基础，由拟合的曲线方程计算接头载荷，并与试验时施加的总载荷对比。
In this method, based on the measured strain values, the joint load is calculated by the fitted curve equation and compared with the total load applied during test.
通常是用万能试验机、液压缸重物或某种形式的压力施加载荷。
Loads are commonly applied with universal testing machines, hydraulic cylinders dead weights, or some form of pressure.
建立板式橡胶伸缩装置的三维有限元模型并施加符合实际工作状况的载荷与位移边界条件。
Make the three-dimensional finite element model about plate rubber expansion device. And then the models are applied serviceable load and displacement.
该装置将试样通过上、下夹头安装在主承力框架内，利用弹簧对试样施加轴向载荷，使试样承受恒定的拉伸应力。
The specimen was put in framework by top and bottom fixture and constant tensile load was applied by spring.
在灭火炮的发射过程中，对发射装置施加的是冲击载荷。
In the process of cannon shot, the load impact has been imposed on the cannon.
在实验中应用负载模拟器产生一种类似真实气流阻力的载荷，施加于弹翼（尾翼），使其能在与展开过程中受力相同的状态下工作。
A kind of load like real airstream is produced by load simulator in experiment , which is put on missile's wings to make them work on the same force situation as in the real spread process .
第二步，模拟实验条件，对模型施加边界约束，把实体模型转换为有限元的数学模型，并利用屈曲分析，对瓦楞纸板竖向边压的临界载荷进行计算。
Second, Simulating experiment condition, putting constraint on boundary of model, changing entity model to finite element model and using buckled analysis to calculate the CD critical load.
研究了施加载荷、压头形状、基板性质等因素对涂层显微硬度测试结果的影响，得出了为准确确定涂层硬度指标所适合的试验条件。
The applied load, shape of the indenter and properties of substrate that have influences on microhardness test result have been studied.
再将温度引起的热应力和外力(如边界条件)之和作为力载荷施加到物体，求得总变形量。
Exert hot stress and external force (such as border terms) that temperature cause as the strength load the object and then, try to get total deformation amount.
然后根据静态力学的有关知识，提出了立柱三种静态工况的模拟，并施加载荷对立柱进行静力有限元分析。
Referring to static mechanics, three types of static operating conditions are simulated and static finite analysis is made after the loads are applied.
从载荷的施加、约束的建立到网格单元的划分，本文详细介绍了混凝土泵车底架有限元模型的具体建立过程。
The concrete establishment progress of the truck mounted concrete pump's frame is presented from the exertion of loads, the establishment of restraints to the creation of meshes.
在有限元模拟中，为了贴切实际加工过程，引进生死单元算法来模拟材料去除过程，通过动态施加载荷步来模拟刀具的运动。
In the course of FEM simulation, the birth-death element arithmetic was introduced into simulating material remove, and the kinetic Load-step was used to simulated tools work.
由于移动最小二乘法的近似函数不一定精确地通过计算点，从而使本质边界条件的施加和集中载荷的处理变得复杂。
This is a disadvantage of EFGM as it suffers from problems in the imposition of essential boundary conditions and the application of point loads.
在模型输入端输入转矩作为动力，在输出端施加各种模拟载荷，仿真后得到了与实验基本一致的动力响应曲线。
Torque acted at the input side as driving power, and the simulated load was put at the output side, and dynamics splines, which were almost equivalent to the results of experiments, were got.
载荷用螺旋式机械施加并保持不变，以保证打印出的位移能够和已知载荷相适应。
The load was applied and held constant by a screw-type machine to insure that the displacement printout could be paired with a known load.
因此，本质边界条件的施加和集中载荷的处理变的复杂。
This is of disadvantage in EFGM for it complicates the imposition of essential boundary conditions and the application of point loads.
按照上面所获得的载荷分布规律，把载荷施加在有限元模型上，利用ANSYS计算，得到了应力的分布规律。
On the bases of pressure distribution, applied the load on the element, after a large number of computer runs by using ANSYS, obtained the stress distribution on the worm and worm gear.
随着施加在煤样上的载荷增加，钻孔冲击次数显著增多，冲击强度增大。
Along with the load increasing that ACTS on the coal sample, the burst frequency obviously rise and the burst intension also rise.
对该模型施加适当的约束和载荷，通过预前共轭梯度法，计算得到了轴类零件在常见工况-弯曲和扭转载荷作用下的位移、应力、应变等力学特性。
Results of displacement, stress and strain of the shaft under the common loads of bend and torsion are obtained by Pre-condition conjugate gradient method.
金属塑性成形是一种利用金属材料的塑性，对金属毛坯施加适当的能量和载荷，使金属毛坯发生塑性变形而形成具有一定几何形状和力学性能的零件或半成品件的成形工艺。
Metal forming is a kind of process to form billets into parts with proper shapes and mechanical properties, under huge energy and load by utilizing the plasticity of metal materials.
螺纹轴连接到将轴向力施加到螺纹轴的载荷。
The threaded shaft is connected to a load that applies an axial force to the threaded shaft.
文章最后还介绍了施加预加载荷的装配夹具示意图。
Sketch of assembling jig used for preloading is showed, too.
从模型的建立，到载荷的施加，再到临时支撑位置的优化，全部过程都是应用APDL语言进行编程计算。
During the entire process of creating finite element model, imposing load and optimizing the location of the temporary supports, the APDL language is used.
从而解决了施加可控冲击载荷和冲击条件下数据测量的问题。
The problem how to act controllable shock load and how to measure the dat...
从而解决了施加可控冲击载荷和冲击条件下数据测量的问题。
The problem how to act controllable shock load and how to measure the dat...
应用推荐