并通过试验证实该方法的可靠性。
The reliability of the proposed method is demonstrated by experiment.
实验结果证明了这两种方法的可靠性。
The reliability of the two methods are certified by result of experiment.
最后还证明了该方法的可靠性和完全性。
The soundness and completeness of this method are also proved.
最后分析了桩基自平衡测试方法的可靠性。
Reliability of self - balanced test method is analyzed at last.
目的探讨心室复极离散度测定方法的可靠性。
Objective To evaluate reliability of methods in reflecting ventricular repolarization dispersion.
实际运行验证了量化pid方法的可靠性及实用性。
The reliability and practicability of quantization PID method have been proved through practical verification.
目的探讨我科心得安试验采取的操作方法的可靠性。
Objective To explore the reliability of the operations used in Propranolol test.
通过与FD - TD法比较，证明了该方法的可靠性。
This method is verified by comparing itS results with that of FD-TD method.
通过零偏VSP理论模型试算，证实了这种方法的可靠性。
Tests on synthetic zero-offset VSP data showed that the method is reliable.
通过建设实践，证实了文中提出的设计及评价方法的可靠性。
The reliability of designing and evaluation method proposed in the article is approved by the practice of underground gas storage construction.
通过大田产量试验验证，本筛选方法的可靠性可达76.9%。
The field test showed that the reliability of this method could reach 76.9%.
通过实测数据验证了这种方法的可靠性和精度，得出了相关的结论。
Through the measured data, the reliability and precision of the suggested method is verified, and relative conclusions are drawn.
目的评价颈前路减压融合术后椎间高度变化的四种测量方法的可靠性。
Objective To study the reliability of four methods for the measurement of intervertebral height after anterior cervical decompression and fusion.
用多种基准物质绘制了不同柱长的校正曲线，证明了新方法的可靠性。
Calibration curves were drawn with some standard substances, so the reliability of the new method established in the paper is proved.
该方法打破了传统的设计规律，为验证该方法的可靠性进行了模型试验。
It has broken the conventional law of design. A model experiment was conducted in order to demonstrate the reliability of this method.
通过对实际轧件的试验研究，充分地验证了这一理论及工艺方法的可靠性。
The reliability of the process is verified by the rolling test for shafts used in small tractors.
评述了高激发核的激发能及核温度的测量方法，以及这些测量方法的可靠性。
The methods measuring excitation energies and temperature of highly excited nuclear matter and their reliability have been summarized.
本研究的目的是评估现有方法的可靠性及取得正常人应用这些方法的测量值。
The aims of this study were to evaluate the reliability of the current methods and to derive normal population values with these methods.
通过对反相色谱二元和三元体系操作参数的优化选择，确证了方法的可靠性。
The validity of the method is verified through the selection of optimal operating condition in binary and ternary mobile phase systems.
提出平均场壳模型下原子核单体密度矩阵的一种计算方法，验证该方法的可靠性。
A method calculating one body density matrix of nucleus in the mean field shell model is proposed.
然后采用数值算例说明了进行非线性分析的必要性及本文差分方法和简化分析方法的可靠性。
Numerical example demonstrates the necessity of non-linear analysis and the feasibility of the difference solution and simplified solution.
介绍了基于位移变量的三维格子法理论，通过对比隔振现场测试结果，验证了方法的可靠性。
The three dimensional grid method based displacements variables was presented and validated through comparing vibration isolating results obtained by grid method with them by field test.
本文采用原子吸收分光光度法，测定铁强化盐中微量铁。用数理统计方法检证了方法的可靠性。
The paper reports atomic absorption spectrum for determination of trace Fe in additional Fe salt. The reliability of this method is examined by mathematical statistics way.
在测点数据有限的情况下，探讨定向钻孔轨迹的模拟方法，并通过实例分析模拟方法的可靠性。
Simulation method of directional drilling course was discussed under limited survey point data, and the reliability of simulation method was analyzed with cases.
反演出的三维风场再与MM 5数值模式输出的三维风场加以比较，验证此种反演方法的可靠性。
The retrieval atmospheric three-dimensional wind field are compared with the three-dimensional wind field output by MM5 numerical simulation to show the reliability of this retrieval method.
试验中采用专用的扁式液压千斤顶，并采用试验室足尺模型标定试验，研究了这种方法的可靠性。
The reliability of this technique, which is based on the use of special flat-jacks, has been studied by means of calibration tests carried out in laboratory on large size samples.
本文详细介绍了锚杆检测技术的原理和计算方法，并通过实例阐述了该方法的可靠性及其实际效果。
The paper detailed introduced the principle and computational method for anchor pole detection technique and expounded the reliability and practical effects of the method by cases.
最后通过滤波器加载输出腔的模拟计算结果与冷测结果的比较和分析，进一步验证该方法的可靠性。
Finally, a output cavity loaded with a filter is computed and the computed result is analyzed and compared with cold test data in order to conform the reliability of this simulated computation method.
最后通过滤波器加载输出腔的模拟计算结果与冷测结果的比较和分析，进一步验证该方法的可靠性。
Finally, a output cavity loaded with a filter is computed and the computed result is analyzed and compared with cold test data in order to conform the reliability of this simulated computation method.
应用推荐