目前它是国内最大断面的方坯管式结晶器。
It is currently the largest - section bloom tubular mould in China.
方坯由于缺少生产任务,未测试使用寿命。
Lack of producing task, the square mould lifetime is not tested.
综合考虑,低拉速有益于普碳钢方坯内部质量的提高。
Comprehensive consideration, low drawing speed is good to the improvement of internal quality.
为合理利用中间圆孔型轧制方坯工艺规程的制定提供了依据。
The results are helpful to rationally developing rolling procedure for intermediate round pass to roll square billet.
比较详细分析介绍了方坯连铸机各主要机构的液压控制系统。
Here is an introduction in detail, together with analysis, to the hydraulic control system for the main components of billet caster.
介绍了邯钢方坯连铸机浸入式水口的改进,保护浇注效果显著。
The improvement of immersion nozzle in square billet caster is introduced, the result extinguished.
被轧制和加工成为梁、棒、薄板的不锈钢产品,如方坯或厚板。
Stainless steel products such as blooms, billets, or slabs that are then rolled and processed into beams, bars, sheets, etc.
建议尽快进行稀土处理方坯低碳钢专用保护渣的研究开发工作。
It is recommended that research and development work about the special mould flux for the rare earth treated low carbon steel billets be carried out as soon as possible.
通过采取相应的改善措施,使方坯切割断面的平整度得到提高。
The leveling of the cutting section of the billet has been greatly improved since adoption of a few counter measures.
分析了影响柳钢热装热送方坯检验的各种因素,制定相应的措施。
The all kinds of factors that affecting the testing of hot-charging and hot direct charging billets and countermeasures were introduced.
通过物质平衡原理讨论并新建立了计算方坯中心缩孔的数学模型。
The updated mathematic models for calculation of the central pipe formotion in continuous cast billet are built up, based on the material balance and the previous published models.
安阳钢铁公司德马克方坯连铸机中修改造后,生产创出了新水平。
The Demag billet continuous casting machine at Anyang Iron and Steel Company has achieved a high output of new level after reformed during medium-term maintenance.
在方坯横截面上,铸坯表面中心和角部的收缩量明显大于偏角部。
In the cross section of square billet, the shrinkage values in the center of billet surface and billet corner are obviously bigger than that in the off-corner.
运用图像分析和模式识别技术,实现非接触式的方坯自动定尺切割。
The technology of using image analysis and pattern recognition to implement the non-touching automatic billet cut-to-length is mainly introduced.
采用声发射燃速测试方法研究了复合固体推进剂方坯燃速的均匀性。
The homogeneity of certified reference material is studied by acoustic emission method for composite solid propellant burning rate.
本文介绍了方坯连铸机结晶器液压振动控制系统及监测系统的组成和功能。
This paper studies the structure and function of remote monitoring system about Billet Caster's hydraulic crystallizer.
并对钼方坯旋锻归圆前道次压缩比的大小对钼产品质量的影响进行了研究。
The influence of magnitude of the reduction ratio on the products quality was studied.
介绍了马钢第三炼钢厂新建方坯连铸机二冷水系统的工艺过程及其控制与特点。
This paper introduces the operating process and control system of the secondary cooling water of the new billet caster in No. 3 steelmaking plant of Magang.
研究了辊道、秤体升降以及方坯剪切的控制方法,给出了方坯在线称重的控制方案。
Working out the control methods of conveying, moving up and down of weighing equipment and billet cutting, the control solution of online weighing of billets is proposed.
分析并设计了方坯连铸机外弧侧扇形段框架加工工艺及装配、调整、检测弧度的方法。
Design and analyze the machining process, assembly adjusting and inspecting methods of square billet continuously founding machine external arc side sector section frame.
介绍了4号方坯连铸机铸坯质量检验的模式,并对检验过程中存在问题提出改进措施。
The quality check mode of No. 4 billet caster has been introduced, and the innovative approaches for problems existing in the check have been put forward.
但连铸方坯的热送直轧新工艺在大规模工业化生产中的应用我国迄今仍未见有成功的报道。
But it hasn't the report about this new technology of the continuous casting square billet made well applied in large-scale industrialized.
针对包钢连铸方坯的中心裂纹缺陷的形成原因进行分析,并提出减少中心裂纹的相应措施。
The article analyzes the causes of formation of central cracks of Bloom of Baogang and puts forward measures to decrease it.
介绍转炉炼钢厂优化3号方坯连铸机的生产工艺,使生产稳定性提高,铸坯质量得到改善。
The process optimization for No. 3 Billet Caster at Converter Plant which improves the production stability and strand quality has been introduced.
对影响方坯铸坯切割端面平整度的相关因素进行分析优化,提出措施,并在生产中得以解决。
The influence of the relevant factors on bloom smooth cutting is discussed and the optimum measures are put forward, and the problem in production is solved as a result.
研究了不同加载方式下TA15钛合金方坯先加载区、过渡区和后加载区的组织和力学性能。
Tensile properties and microstructure of the first loading region, last region and transition region of TA15alloy parts with different local loading were studied by experiment.
该方坯取料装置结构合理,运行平稳,对钢坯及辊道基本无冲击、无噪音,使用情况较为理想。
Billet device from the rational structure, the smooth running of the billet roller and basically shocks, no noise, the use of a more satisfactory.
应用流场计算软件PHOENICS及水力模型,模拟了方坯连铸结晶器内钢液的流场和流动分布。
Using flow field software PHOENICS and water model, this paper describes the flow field of molten steel in continuous casting billet mold.
提出了一种通过测量方坯截面面积在线计算方坯质量的方法,通过该方法可以实现方坯的定重剪切。
A new on-line calculation method for billet weight by measuring its cross section was presented, and cut-by-weight of billets could be realized by this method.
并以球冲头压缩方坯和曲轴成形为例进行了模拟,计算结果表明所提出的算法和软件系统是可行的。
Compression of square block with hemispheric punch and forming of crankshaft are simulated by this system, which indicates that the given methods and software are feasible.
应用推荐