中间层和顶层平面外部创造了动态的黑白斜螺旋块，他们交错在一起。
The middle and the top floor exteriors create dynamic black and white sloped spiral blocks which are twisted together.
分析齿轮主要参数，提出用测量跨棒（）和公法线长度计算斜齿圆柱齿轮螺旋角的测绘方法，并推导出螺旋角的计算公式。
In this paper calculating method of lead angle of helical gear by measuring span length of length bar and base tangent length is put forward and lead angle calculating formula is deducel.
给出了斜航式法向圆弧螺旋锥齿轮的参数化建模方法。
The parametric modeling method for loxodrome normal circular-arc spiral bevel gear was presented.
利用直齿齿轮泵的困油容积变化公式，求出了斜齿齿轮泵的困油容积变化公式，得到了斜齿齿轮泵不发生困油的螺旋角。
According to the volume oil formula of the straight gear pump, the volume oil formula of the helical gear pump is got and the helix Angle no trapping is found.
因此，利用数字控制取代螺旋导轨，实现斜齿插削加工的CNC控制具有重要的现实意义。
So using CNC substitute helix track and realizing bevel wheel's shaping CNC have important realism meaning.
比较结果表明，利用本文提供的方法可望提高大侧斜螺旋桨性能的计算精度。
It is confirmed that the accuracy of calculation results can be improved, especially for highly skewed propeller, by the present method.
分析螺旋面斜向扭转振动传动的原理和螺旋面上物料运动的规律。
This paper analyzed the movement theory of lean rotate Vibration of helical surface and the motion law of materials movement.
介绍了螺旋焊管成型器内压辊斜置小辊线接触辊型的设计方法（经验公式设计法）。
The article introduces the design methods of contact roller of internal press roller of forming machine of SSAW pipe mill(experience formula design).
本文阐述了大侧斜螺旋桨设计软件包的功能及其使用特点。
A highly-skewed propeller (HSP) design package has been developed, its feature and function are described.
本文介绍了脱墨浆高浓漂白系统改造过程中浆料输送系统的改造，重点讲述了斜螺旋输送机的设计。
This paper introduces the rebuilding of pulp feeding system of DIP high consistency bleaching, especially describes the design of bevel screw.
目的：探讨螺旋形导针配合双侧斜位X线片判断颈椎椎弓根螺钉置入孔道准确性的可行性。
Objective: To evaluate the accuracy of cervical pedicle screw pilot holes placement by bilateral oblique X-ray films with the spiral wires as the guide pin.
本文主要对这种新型传动齿轮——斜航式法向圆弧螺旋锥齿轮的误差与变异的关系和精度检测进行了较为深入的理论研究。
In this dissertation, the relationship between the errors and variations for the loxodrome normal circular-arc spiral bevel gear (LNCSBG) is deeply studied.
详细分析了斜齿齿轮泵的瞬间排量、单齿排量、困油区容积的瞬间变化率及变化量、螺旋角的影响。
Analyze the Helical Gear Pump for the instant displacement, single gear displacement, theinstant change ratio and change value of trapping volume and the influnce of screw angle in detail.
在该工程中采用了新颖的伞型斜向支撑技术，并利用螺旋式千斤顶进行主动支顶。
In connection with an engineering example, this paper introduces the application of a novel active roof-propping technique which uses umbrella-shaped braces and screw jacks for active propping.
本文从斜流产生螺旋桨侧向力出发，导出舵后桨组合体的综合侧向力。
Depending on the principle of the transverse force of propellers produced in oblique flow, this paper acquires the overall transverse force of propellers after rudders.
目的：探讨多层螺旋CT (MSCT)最大强度投影(mip)测量肩胛孟斜倾角的价值。
Objective: To assess the value of maximum intensity projection (MIP) of multi slice spiral ct (MSCT) in measuring the scapula glenoid inclination Angle.
目前最常见的斜拉索空气动力措施有螺旋线措施和凹坑措施。
The most common cable aerodynamic measures is enlace spiral and press pits on the surface.
以齿轮系统动力学理论为基础，提出了通过斜齿轮螺旋角的择优选取改善系统动态特性的方法。
A method to improve the dynamic characteristics of gear system is proposed through the selection of spiral Angle of helical gear according to gear system dynamics theory.
本文介绍由斜螺旋面和单叶双曲面组成的犁面在犁面主参数确定后的工程作图法。
It's introduced in this paper how to draw the engineering drawing of the plow surface formed by a combination of a oblique helicoid and a hyperboloid of one sheet.
斜向拉荷载作用下，螺旋桩的极限承载力随着叶片距宽比的增大有所降低。
With the increases of RPDD, screw pile's ultimate bearing capacity decreased under inclined pullout load.
由于船体的影响，双桨船的螺旋桨处于斜向来流的条件下运转。斜流造成螺旋桨叶工作状态的非定常性。
Because of the influence of the hull, the stern propeller of a twin-screw vessel is working under condition of oblique flow, and the unsteady working condition of the blade of a propeller is created.
本论文利用FLUENT的这些特点模拟大侧斜可调桨的三维粘性流场，在没有图谱可以利 用的条件下，使 CFD成为螺旋桨设计的手段之一。
This thesis tends to simulate the 3D viscous flow of a high-skew controllable pitch propeller by using FLUENT, which can serve as a design method without collection of illustrative plates.
本论文利用FLUENT的这些特点模拟大侧斜可调桨的三维粘性流场，在没有图谱可以利 用的条件下，使 CFD成为螺旋桨设计的手段之一。
This thesis tends to simulate the 3D viscous flow of a high-skew controllable pitch propeller by using FLUENT, which can serve as a design method without collection of illustrative plates.
应用推荐