另外，讨论了在生长过程中动态调整坩埚盖散热条件的可行性。
Besides, the feasibility of dynamic modification of the heat transfer conditions of the crucible lid was discussed.
并对铜基板尺寸、基板底面散热条件等几项关键参数进行了优化设计。
At the same time the size of the copper substrate and the cooling condition of substrate's bottom are optimized.
压缩机组需有专人管理，必须保持设备的整洁及良好的通风散热条件。
The compressor unit should be managed by the special-assigned people. The equipments should be clean and well ventilated.
通过温升实验样机能够满足国家相关规定，提出进一步改善散热条件的方式。
Some methods of heat dissipation improvement are also introduced. A set of specific high current switch is designed in this paper.
研究了随焊激冷减小铝合金薄板焊接变形的效果及夹具的散热条件对该效果的影响。
Effectiveness of reducing welding distortion by trailing intensive cooling and the influence of heat - dissipating condition of the fixture on such effectiveness were studied.
该结构的主要特点是实现了磁芯窗口面积利用率的最大化，可降低集成磁元件的铜损和改善其散热条件。
It features the maximum utility ratio of the core window areas and can reduce the copper loss and improve the heat dissipation of the integrated magnetics.
通过齿轮箱的情况下的温度和它的字段分布和散热条件的每一个其他的在计算上，从而使计算变得更加困难。
The temperature and its field distribution and the heat dissipation through gearbox case are conditional on each other in computation, thus making the computation much more difficult.
产品全部为高原型，其绝缘强度、运输要求、散热条件、外观等均经过大量研究，能充分满足高原地区的运行要求。
The product is plateau type. Its insulation strength, transportation requirement, radiation condition and overall appearance can sufficiently meet the operation requirement in plateau area.
在固定散热片高度的条件下，提供最佳散热效果的散热片宽度会依据雷诺数提高。然而过度的宽度会造成散热效果下降。
For constant fin height, the fin width that provides the best thermal performance increases with the Reynolds number. Further increasing the fin width will degrade the thermal performance.
分析了低散热发动机的传热特点，运用经验公式确定了传热边界条件；
The heat transmiting character of the Low Heat Rejection Engine is analysed and the heat transmiting boundary conditions of the firebox are computed by experience formular.
实验证明，通过合理的风道设计，可以在散热器和风机参数一定的条件下，有效地提高散热效果。
Experiment proves the cooling effectiveness can be enhanced through reasonable design under the known specifications of the heat sinker and blast fan.
用此方法建立了轮胎温降-时间历程关系式，分析了轮胎散热情况，分析表明温降时间也与使用条件无关。
Then the formula of tire temperature fall history was also derived with the tire heat dissipation analyzed, which came to the same conclusion as the case of temperature rise.
研究了不同的非金属基导热界面材料在不同环境温度条件下，应用于HPLED灯具模型中的第二界面处时对灯具散热情况的影响。
The effect of nonmetallic thermal conductive interface materials on the heat dissipation of HPLED lamp model was studied at the second interface under different temperatures.
发电机 定子散热的边界条件作了妥善处理。
The boundary conditions of scattering heat of synchronous generator are dealed with reasonaby.
揭示了液体流率受管道结构等条件的限制，合理调节范围较窄，服装温度比效率不会很高，应主要靠调节进口液温来改变服装的散热量。
T he flow rate regulation range was too narrow, and the change of heat removing capacity depended on the change of inlet temperature.
在固定散热片宽度的条件下，高度最高的散热片有最佳的散热效果。
For constant fin width, the heat sink with the highest fins has the best thermal performance.
对散热器芯体进行了理论分析与研究，在给定条件下对散热器的性能参数进行了优化计算。
A theoretical analysis and research is done on radiator body and an optimumcalculation about radiator's performance parameters is made in given conditions.
压力辊轴的冷却通常是通过两个条件：使用内部高速循坏的水流速，以及放置一个对着压力辊轴的尾部作为散热器的水冷却铝辊轴。
The pressure roll is usually cooled both by internal circulating high velocity water and by placing a water-cooled aluminum roll against the trailing edge of the pressure roll as a heat sink.
实验系统测试了典型晴天和多云天气条件下太阳能集散热辐射板系统的性能。
The performances of the solar heating and radiative cooling system were measured under typical sunny day and cloudy day.
局部放电量低，噪音小，散热功能强、强迫风冷条件下可以150%额定负载运行。
Local put low power, the noise is small, cooling function of strong, forced air cooling conditions can be 150% rated load operation.
对温度响应的测试结果进行分析可以求得测试条件下的散热系数、耗能情况，同时也可以对干燥窑的性能作出评价。
Through the analysis of the tested results of the temperature response, not only the heat transfer coefficient and the energy consumption under that condition can be found, but also the quality...
但闭式系统较开式系统复杂，因无油箱，油液的散热和过滤条件较差。
However, a more closed system, open and complex systems, because no fuel tank, oil cooling and filtering the disadvantaged.
在肋片外形不变的条件下，增加肋片的厚度来提高辐射器的散热性能并不是经济的途径；
Fixed the fin shape, adding the fin thickness is not an effective way to increase the efficiency.
在肋片外形不变的条件下，增加肋片的厚度来提高辐射器的散热性能并不是经济的途径；
Fixed the fin shape, adding the fin thickness is not an effective way to increase the efficiency.
应用推荐