适用于平面磨床及放电加工机使用。
实验结果表明，自振式晶体管脉冲电源因其加工速度慢并不适于微细放电加工。
The experimental results reveal that the transistor type pulse train generator is unsuitable for micro-EDM due to its low removal rate.
分析了颗粒复合对氮化硅基陶瓷复合材料的火花放电加工性及切削性能所起的作用。
The effect of particles on the electrical discharge machining (EDM) and cutting property of silicon nitride-based composites was analyzed.
铜合金应用制品主要有线割放电加工用电极铜线、空调设备用铜管、散热器用铜管。
The main application products of copper alloy are copper wire for WEDM, copper tube for air conditioner, copper tube for heat sinker.
放电加工中，加工条件可随时进行修改，立即执行，且不必停机，大大简化操作程序。
Discharge in processing, processing can be revised at any time, carry out immediately by condition, And need't shut down, simplify the operation sequence greatly!
它们的应用包括放电加工用的电极、导电金刚石零件、金刚石砂轮以及精密磨削工具等。
The applications of both of them included electrode in EDM, electroconductive diamond parts, diamond grinding wheel and micro precision grinding tools etc.
用ANSYS以有限元软件对超声振动辅助气中放电加工过程的温度场进行了数值模拟。
The temperature fields during ultrasonic vibration aided electrical discharge machining in gas are simulated with ANSYS method and FEM software.
结果表明，用ANSYS来计算超声振动辅助气中放电加工的材料去除率是一种行之有效的方法。
The results indicate that the simulation with ANSYS is an effective way by which the material removed rate of ultrasonic vibration aided EDM in gas can be calcul…
可用于对镜面性、蚀花性、放电加工性要求高的模具，如办公用具、透明外壳、各种树脂产品等。
Mold requiring sensitive surface as mirror polish, creping, EDM. Such as transparent case, OA electronics, Engineering resin products etc.
电火花线切割加工时工具(电极丝)和工件之间的放电电压是对放电加工过程进行实时检测的重要参数。
Voltage between tool and workpiece is an important parameter in the on line monitoring of wire electrical discharge machining (WEDM) process.
综述了日本在放电加工领域的最新研究动态，包括成形放电加工、微细放电加工和线切割放电加工三部分内容。
The newest trends of electrical discharge machining (EDM) including die-sinking EDM, micro EDM and wire EDM (WEDM) in Japan were presented.
重点对超声振动辅助气中放电加工的原理和工艺规律进行了深入的探讨，并从试验结果分析中得出了该技术特有的基本工艺规律。
The mechanism and technology of ultrasonic vibration aided electrical discharge machining in gas were researched. The special technologic rules were acquired based on the experiment results.
超声电火花复合加工实质上就是在普通电火花放电加工的基础上，在工具电极或工件上叠加一个超声振动，以改善放电加工条件。
Virtually, ultrasonic vibration is added to tool electrode or workpiece electrode on the basis of EDM to improve the processing conditions in ultrasonic vibration assisted EDM process.
由于该复合加工技术有效地结合了放电加工和机械磨削加工的特点，并且二者互为有利条件，因而能高效率、高质量地加工陶瓷材料。
Proposes the electro discharge mechanical-grinding(EDMG) which combines the virtues of both EDM and grinding. It can be used in machining ceramics with high efficiency and quality.
建立了电火花放电加工的热力学传导模型，通过有限元仿真方法得出具有放电爆炸力的单次脉冲能够明显提高难加工材料蚀除量的结论。
The heat transfer model of the discharge has been established, and the removal rate could be significant promoted because of the explosion with the method of thermodynamic finite element analysis.
在电火花放电加工过程中，采用负极性加工时，工具电极的损耗主要是由于火花放电前几百纳秒出现的电子流对工具电极表面的轰击造成的。
In EDM process with tool as anode, tool wear is largely produced by electron current in gap during the frist hundreds nano seconds of the spark ignition.
通过建立简易工艺数据库 ，该系统可适用于其它介质中的火花放电加工 ，有助于提高电火花气中放电加工自动化程度和开发智能化加工系统。
Through the establishment of the process database, the simulation system is applicable to electric discharge machining in other medium, it is a help to raise the automation of…
由于气体介质放电加工是一种绿色加工工艺，因此该加工方法受到了国内外电加工研究领域学者的广泛关注，是电火花加工领域的研究热点之一。
The EDM based on gas is a green processing technology, so it is valued by researchers at home and abroad on the field of EDM, and it is one of the research focus on EDM.
简要介绍了电火花脉冲加工的现状、特点及加工原理；着重分析了放电加工中电参数对加工效率及加工精度的影响；定量分析了它们之间的相互影响。
It mainly analyses the influence of electrical parameters on the machining efficiency and precision in the course of electrical discharge, and analyses quantificationally the mutual influence of them.
根据放电时产生的加工液沸腾、气化膨胀引起放电通道周围加工液快速流动的原理 ，提出了一种新的排屑方法 ，系统地研究了使用该方法的放电加工特性。
A new excluding method of debris using the rapid flow due to evaporation of dielectric fluid when discharging was proposed and the EDM characteristics of the method were experimentally discussed.
针对目前航空、航天等领域中日益广泛应用的硬质合金等材料出现的切削加工困难、电加工蚀除速度慢的问题，设计了带有放电爆炸力的电火花加工脉冲电源。
Based on the low removal rate of the material like cemented carbide in the space field by cutting and EDM, a pulse generator discharged with explosion is designed.
针对目前航空、航天等领域中日益广泛应用的硬质合金等材料出现的切削加工困难、电加工蚀除速度慢的问题，设计了带有放电爆炸力的电火花加工脉冲电源。
Based on the low removal rate of the material like cemented carbide in the space field by cutting and EDM, a pulse generator discharged with explosion is designed.
应用推荐