所要做的只是将单元用四个螺栓固定到其支承表面上。
All that is needed is to bolt the unit to its support using four bolts.
一可透射外壳包括确定偏转器相对于发生器支承表面为斜角方向的锯齿部分。
A transmissive enclosure includes indented portions defining deflectors oriented obliquely with respect to a generator support surface.
有径向凸缘及在与轴承轴心线垂直的支承表面上有供其安装用的螺钉孔的一种座。
A radial flange and in line with the bearing axis perpendicular to the bearing surface for the installation of a screw hole with a seat.
这种新的假体是一个移动-支承装置，它所依赖的支承点可以在一个聚乙烯的弹性塑料表面移动。
The new prosthesis is a mobile-bearing device, which relies on bearings that move across a surface of polyethylene, a flexible plastic.
对于不同内部介质接触的部件，如外表面、防护罩及支承凸缘等不需腐蚀余度，地脚螺栓除外。
No corrosion allowance is required for such parts not in contact with the inside fluid as the outside surface of shell, skirt, support lugs and so on, except for anchor bolts.
本机由主机用工作台组成，工作台上表面装有均布的万向轮，用于支承需要磨削棱边的玻璃。
The surface of work table is equipped with equispaced universal wheel to support the glass which need be edged.
引导件(4)由壳体(1)支承，并包括与电流条(3)的至少一个表面相连接的引导表面。
The guide (4) is supported by the housing (1) and comprises guide surfaces that connect with at least one surface of the current bar (3).
编制了发动机表面或其他机器表面辐射效率计算机程序，并提出了固定支承边界和带加强筋平板的处理方法。
The computer program for calculating radiated efficiency of engine or of other machine surface has been compiled and treatment of Clamped boundary conditions and ribbed plates are proposed.
一个实例包括支承于表面(38)上的显示板(42)，该表面通常放置于扶手(28)与楼梯平台(24)之间。
One example includes a display panel (42) supported on a surface (38) that is conveniently positioned between a handrail (28) and a landing (24).
对连轧机精轧支承辊大面积剥落的原因进行了深入的分析，结果表明，轧辊内部的缩孔、气泡及热处理不当是造成轧辊表面剥落的主要原因。
It has been analysed the causes for the heavy surface spalling of back-up roll for a finishing mill. The result shows that the main causes are gas hole, shrinkage and bad heat treatment.
每个支承构件包括弯曲的下表面(146)和位于支承构件的下表面的凹进部分内的滚动元件(148)。
Each support member comprises a curved lower surface (146) and a rolling element (148) located within a recessed portion of the lower surface of the support member.
在两种不同的运动副表面粗糙度下，分别讨论了配流盘静压支承的主要结构参数对最小水膜厚度的影响。
The influence of the primary structural parameter on the minimal water film thickness will be respectively discussed in two different rough degree.
表面紧固件的另一对应的表面在支承板上。
Another corresponding surface of the surface fastener is on the supporting plate.
本文介绍了用局部不接触法修复轧机支承辊表面裂纹的方法。
This article recommends a local noncontact method to remedy the surface crack on the backup roll of the hot rolling mill.
提供一种充电构件，其具有支承体、形成于该支承体上的导电性弹性层和形成于该导电性弹性层上的表面层。
A charging member is provided having a support, a conductive elastic layer formed on the support and a surface layer formed on the conductive elastic layer.
较长的纳米结构化支承元件提供了更大的支承催化剂材料的表面积，从而允许在所述层上填塞更多的催化剂。
Longer nanostructured support elements provide increased surface area for supporting catalyst material, thus allowing higher catalyst loading across the layer.
套在支承管外表面的磁性套筒(6)与支承管间隙配合。
A magnetic sleeve (6) is sheathed on the outside surface of the support tube and is in clearance fit with the support tube.
这种完井方法的主要缺点在于生产层表面没有被支承并可能坍塌。
This type of completion suffers the major disadvantage that the sandface is unsupported and may collapse.
滚动元件的外表面与支承构件的下表面所描述的轨迹(149)或虚拟表面基本一致。
The outer surface of the rolling element is substantially coincident with a locus (149), or virtual surface, described by the lower surface of the support member.
辊套(1)的热处理性能好，硬度均匀，硬度梯度从表面层向芯部下降梯度小。因此镶套支承辊的使用寿命长。
High heat treatment performance of roller sleeve (1), uniform hardness, reasonable hardness gradient, thus ensure the long service life of inlaid backup roller.
辊套(1)的热处理性能好，硬度均匀，硬度梯度从表面层向芯部下降梯度小。因此镶套支承辊的使用寿命长。
High heat treatment performance of roller sleeve (1), uniform hardness, reasonable hardness gradient, thus ensure the long service life of inlaid backup roller.
应用推荐