推力球轴承的设计处理轴向负荷只。
Thrust ball bearings are designed to handle axial loads only.
双向推力球轴承，其中圈与轴配合。
在双向推力球轴承可以承受双向的负载。
The double direction Thrust ball bearings can support bi-directional loads.
向心推力球轴承特别适用于承受合成载荷。
Radial thrust bearing is especially fit for enduring composed load.
单向推力球轴承可承受单一方向的轴向载荷。
Single thrust ball bearing can be subject to the axial load from single direction.
推力球轴承能承受两个方向的交变轴向载荷。
Thrust ball bearing is separable bearing and only can be subject to axial load.
采用圆锥滚子轴承取代现有的轴向推力球轴承。
The tapered roller bearing replaces axial thrust ball bearing.
推力球轴承不能承受径向负荷，极限转速较低。
Thrust ball bearings can bear radial load, lower speed limit.
推力球轴承是可分离型轴承，只能承受轴向载荷。
This type of bearings is separable, which can only carry axial load.
对在航空发动机滑油系统断油时的主推力球轴承瞬态热进行了分析。
The transient thermal analysis of the main thrust ball bearing was performed during fuel cut off for an aeroengine oil system.
推力球轴承包括球，保持架和两轴和轴承座垫圈其中所包含的球槽。
Thrust ball bearings consist of ball, retainer and both shaft and housing washers which contain grooves for the ball.
也有单方向和双向推力球轴承球形表面和带有相应的支持形座位垫圈。
There are also single-direction and double-direction thrust ball bearings with spherical supporting surfaces and correspondingly shaped seating washers (Figure 1.49).
在转速较高不宜采用推力球轴承的情况下可用该类轴承承受纯轴向负荷。
The higher the speed should not adopt thrust ball bearings available class bearings are subjected to purely axial load.
为减小喷涂机构摆动过程的阻力，喷涂机构的定位方式采用了类似推力球轴承的结构。
To decrease resistances during swing of the rocker, the bearing was adopted to Orient spray mechanism.
同时又对滚子端面的小型推力球轴承推导出接触应力、疲劳强度和静载强度的计算公式。
Also, the calculation formula of the contact stress, the fatigue strength and the static strength for the small thrust bearing which are attached at the end face of roller are derived.
轴承采用了单列向心推力球轴承，这种轴承具有同时承受较大的轴向荷载和径向荷载的能力。
Bearing a single row thrust ball bearings to the heart, which has at the same time to bear a greater bearing axial load and radial load capacity.
泵轴向力与径向力，均由轴承盒内所装单向推力球轴承，单列向心球轴承及滑动导轴所承受。
Axial Force and radial Force of the pump are bore by single-direction thrust ball bearing, single-row radial ball bearing and sliding guide axle.
推力球轴承是专为支持轴向力设计的，他们用于轴向力过高，可以由径向轴承传播(的地方)。
Thrust ball bearings are designed for supporting axial forces; they are employed where axial forces are too high to be transmitted by radial bearings.
角接触推力球轴承在高速运转时，作用在球上的离心力和旋转力矩可能会导致钢球在滚道内滑动。
When angular contact thrust ball bearings operate at high speeds, the centrifugal forces and gyratory moments acting on the balls may cause them to slide on the raceways.
FST生产的推力球轴承以单向推力球轴承为主，同时还生产双向推力球轴承及双向推力角接触球轴承。
FST production to one-way thrust ball bearings thrust ball bearings mainly, but also the production of two-way thrust ball bearings and two-way thrust angular contact ball bearings.
FST生产的推力球轴承以单向推力球轴承为主，同时还生产双向推力球轴承及双向推力角接触球轴承。
FST production to one-way thrust ball bearings thrust ball bearings mainly, but also the production of two-way thrust ball bearings and two-way thrust angular contact ball bearings.
应用推荐