同时建立了该液压电机泵变速控制系统的数学模型。
The model of hydraulic motor pump variable speed control system is built.
为了便于分析与设计,文中建立了控制系统的数学模型。
In order to facilitate the analysis and design, mathematical models of control system are established.
本文推导了有不同采样周期的计算机控制系统的数学模型。
This paper provides mathematics model for computer control system with different sampling cycle.
提出了高起始响应励磁控制系统的数学模型和考核试验方法。
The mathematic model of excitation control system with high initial response and the method of assessment test are also introduced.
建立了液压伺服控制系统的数学模型,并进行了简化和离散化;
The model of the hydraulic servo system is created, simplified and dispersed.
首先,建立了阀控非对称缸位置控制系统与力控制系统的数学模型。
At first, it studied the plant model of position and force system about valve control unsymmetrical hydraulic ram.
通过分析磁轴承系统中的电磁关系建立磁轴承控制系统的数学模型。
The mathematical model of magnetic bearing system is established by analyzing the relationship between the electromagnetic magnetic bearing control system.
分析了非对称气动伺服阀控单作用气缸的气动压力控制系统的数学模型。
The mathematical model of a pneumatic force control system with an asymmetric servovalve and a single-acting cylinder were described.
针对液压伺服驱动连铸结晶器控制系统的数学模型,设计了预测控制器。
Aiming at the mathematical model of continuous casting mold control system driven by the hydraulic servo system, the predictive controller is designed.
分析软并网控制系统的数学模型,建立软并网控制器最优控制数学模型。
Mathematical model of soft cut-in control system was analyzed, and the optimum control model also is established.
以实验为基础,建立了闭环温度控制系统的数学模型,构造了相应的PID控制器。
Based on the experiment, the mathematical model of close-loop temperature-controlling system and PID controller were constructed.
为了实现自主车跟踪固定路径的精确控制,建立了自主车路径偏差控制系统的数学模型。
A mathematic model has been established in the article for the control system about the path deviation of ALV (Autonomous Land Vehicles) in order to control its tracking navigation route accurately.
给出了液压阀的设计要点、控制系统的数学模型及采用单片机为核心的PID控制系统。
The study indicated the key of the hydraulic valve design and introduced the mathematical model of the control system and the PID control system of the single chip microcomputer control.
建立了主从式同步卷绕控制系统的数学模型,并详细介绍了控制系统硬件和控制方法的具体设计。
The mathematical model of master-slave synchronous winding control system is established here, and the design methods of the system hardware and control method are introduced in detail.
采用磁流变阻尼器半主动控制理论和方法,建立座椅可控磁流变阻尼非线性控制系统的数学模型。
Using magneto-rheological damper, semi-active control theory and method, mathematical model of a controllable magneto-rheological damping and nonlinear control system is established for seats.
根据非回转体环向缠绕理论及叶片产品的具体要求,分析缠绕工艺,建立了张力控制系统的数学模型。
Next, according as no - gyrating round fiber winding theory and concrete request of vane, analyzing the winding technics, found the mathematics model of tension control system.
应用机理分析建模和灰箱建模相结合的方法,建立了单轴燃气轮机发电机组及其控制系统的数学模型。
Applying the method of combining the mechanism analysis modeling and gray box modeling, the mathematic model of the single-shaft gas turbine generating units and the control system was established.
其次,建立了两种主流液舱阀门控制系统的数学模型,分析了它们的动态特性,指出了它们的适用范围。
Secondly, the mathematical models of the two mainstream fluid hold valves' control systems are given, dynamic characteristic is analyzed, applicable range of them is indicated.
本文充分考虑了网络化控制系统的随机时延,分析了网络时延的时序,并构建了网络控制系统的数学模型。
In this paper, considering the random time-delay of NCS, We analyze its sequence and set up the mathematic model of NCS.
仿真结果表明,与实际飞行试验数据达到非常好的拟合,说明采用六自由度的制导控制系统的数学模型进行设计的正确性。
Numerical simulation results for sample engagement scenarios are given. It shows that simulation results are very close to the actual flight test results. So …
首先推导了下位机关节位置伺服控制系统的数学模型,然后推导了在上位机上实现的滑模变结构控制率,并进行了实验研究。
First, the mathematic model of joint position servo control system is deduced, then, the sliding mode variable structure control rule is obtained, finally experiment study is carried through.
根据造纸过程中纸张张力的特点及控制要求,建立了控制系统的数学模型,提出了一种具有自适应能力的模糊pid控制器,分析了控制器的结构和规则。
According to the characteristics and control quality for tensile force of paper, the module of control system is estimated and a fuzzy PID controller with adaptive ability is put forward in the paper.
本文还建立了此闭环控制系统的数学模型,通过数字仿真分析了其动态特性,探讨了控制器参数对转子运动的控制效果以及与电磁轴承动刚度之间的变化关系。
Also this closed loop controlled system is modelled and its dynamic behaviors are analyzed by digital simulation. The influence of controller parameters on motion of the rotor and th...
该文介绍了锂离子电池的生产工艺流程及其薄膜卷绕控制系统,建立了薄膜卷绕控制系统的数学模型,提出采用内模控制算法,并对相应的控制模型进行了仿真。
The paper introduces the li battery production process and the film rolling control system, building the model of control system, adopting the IMC arithmetic and making simulation.
建立燃气轮机数学模型是船舶动力及其控制系统研制的重要手段,建模的关键在于提高精度和收敛速度。
The mathematic model of gas turbine engine is important for the development of ship power and its control system. The key of modeling is the precision and convergence.
掌握被控对象的数学模型和建模后控制系统的设计,是过程控制系统分析、设计、调试和获得较高控制品质的基础和关键。
The math model and control system design after modeling are the base and key point to process control system analyses, design, debug and obtain the higher control quality.
本文叙述并分析了烧结终点微机控制系统的原理,提出了实用的控制方法和数学模型。
This paper describes and analyzes the principle of microcomputer system controlling sintering burn-through point, and provides its practical control methods and mathematical models.
本文阐述了一个基于动态数学模型及启发式优化策略的连续加热炉计算机控制系统的设计与实施。
The design and implementation of reheating furnace computer control system based on the dynamic mathematical model and the heuristic optimization strategy is discussed in this paper.
本文先对纺织、印染等行业中的多单元传动控制系统进行分析,建立系统的数学模型。
This paper first analyses the multicell drive controlling system in textile or printing and dyeing industry, then form the mathematical model of it.
针对三相异步电机矢量控制系统的要求,根据在静止坐标系统中异步电机的数学模型,进行了系统仿真。
The thesis introduces a three phase AC motor's mathematical model in static reference frame and a simulation system for AC motors to develop a vector control inverter system.
应用推荐