这样ria开发人员就能够开发包含Flex模块的OSGi束，而最终用户也可以使用基于Flex的接口安装和控制它们。
This will enable RIA developers to develop OSGi bundles that contain Flex modules, so end users can use the Flex-based interface to install and control them.
蓝牙规范包含了一个符合标准的接口定义(主机控制器接口)，它适用于蓝牙通讯模块的硬件部分。
The Bluetooth specification includes the definition of a standardised interface (the Host Controller interface) to the hardware of a Bluetooth communications module.
该方案的系统组成包括PC机软件、LXI接口电路、控制模块、多通道dds系统和加法器。
This system could include the PC software, LXI interface circuit, control module, multi-channel DDS system, and the Adder module.
通过多次仿真与模拟，该模块还能与工控机以及具有通讯接口的任何辅助器件进行通讯，完成复杂的工业控制。
When emulated and simulated, the module can also communicate with industrial control unit and any other assist devices having communication port to realize complicated industrial control.
主要介绍CPCI数字存储示波器模块的模拟通道设计、A/D采样设计、数字控制电路设计、电源设计以及CPCI接口设计。
The hardware design of the module mainly presents analogue channel circuit design, A/D acquisition circuit design, digital control circuit design, power and CPCI interface design.
方法：应用蓝牙模块、80c 552微控制器和RS- 232接口组成了医院导诊服务机器人的通讯系统。
Method: the communication system in the service robot side includes80C552micro-controller, bluetooth module and RS-232interface.
该冗余驱动接口模块刚度好，且其中各驱动单元间的力均衡误差小，可避免使用成本高、算法复杂的力反馈控制技术。
The force unevenness between two driving units of the interface module is so small that force feedback control technique is not needed.
该方法利用单片机控制蓝牙模块，采用基于HCI层的单片机对蓝牙模块控制的方法及PC机端通过RS232接口连接蓝牙模块互相配合，实现PC机与能动磨盘之间的通信。
The method carries out the wireless communication between the PC and active lap, by the conjugation of bluetooth module controlled by MCU via HCI and bluetooth module connected with PC via RS232.
重点讨论了访问、控制硬件接口模块的设计。
The emphasis is about the design of interface module used to access and control the hardware.
FPGA不仅要实现语音时隙交换的功能，还要与接口电路模块、号码分析模块、调度控制模块进行通信。
FPGA should not only implement the voice slot switch function, but also communicates with the interface module, caller-ID analyzing module and controlling module.
本文很详细地介绍了DMA控制用户逻辑的各个模块，包括其接口和状态机。
In the article, we introduce each module of DMA controller custom logic including the interface and the state machine.
本文以内藏液晶显示控制器（T6963C）的液晶显示模块为例，介绍了其在DSP测控系统中与DSP芯片（TMS320C542）的软件和硬件接口形式。
The article takes the LCD module of T6963C controler with built-in LCD for example, presenting its software and hardware interface with DSP(TMS320C542) in DSP application.
采用CAN总线作为模块间的通信接口，有效地支持了多关节实时控制。
CAN bus is introduced as the communication interface for different modules and it supports the multi joints 'real-time control effectively.
软件部分包含模块接口的实现和控制算法的实现。
The software contains implementation of the interface modules and control algorithm.
本课题研究在微控制器系统中，把嵌入式usb主机接口作为一个功能模块，实现了车载多媒体视音系统嵌入式usb主机的的实际应用。
This study applys embedded USB HOST interface as a module to the Microprocessor and realizes the practical application of embedded USB HOST to the auto-multimedia system.
外部设定与保守模块主是用户管理和系统控制的接口，用户可以通过输入系统命令获得系统信息或者改变系统的工作状态。
External setting and keeping module is the interface of user administration and system control. User can get system info or change operating mode of system by inputting instruction.
其控制方式为间接控制，即P 89c 669通过自身系统中的并行接口与显示模块连接。
Its control manner is indirect control manner, that is, the P89C669 connected with display module by using parallel interface.
介绍了TMS320F240串行通信接口模块的特点及构成，并结合一个电机控制系统对串行通信接口的实际应用进行了说明。
This article introduces serial communication interface module(SCI)of TMS320F240. It also combines with an example of motor control system to explain practical application of SCI module.
负责电子控制模块微控制器接口的故障诊断。
Trouble Shoot Electronics control Module Microcontroller Interface.
该系统监控所有可能的内核模块加载接口，根据设定的保护域和用户验证对内核模块加载进行控制。
This system watches on every possible interface were used for loading, and the loading according to the protected-region and user qualification were controlled.
可编程网络的目的是打破封闭式的网络模型，通过特定的对外接口、控制机制和内部处理模块实现网络设备的功能可编程。
Programmable network will break through the traditional rigid closed model and offer programmability via dedicated interfaces, control mechanism and processing model.
通过T6963 C控制器的液晶显示模块在医用分析仪器上的使用实例，比较了使用该控制器的液晶图形模块时的不同硬件接口形式。
With the examples of use in medical instruments about LCD display module based on inner T6963 controller, two diverse hardware interface forms when using the controller were discussed.
其设计包括不同数据节点的CAN控制器，及单片机控制的CAN接口模块和基于DSPTMS320 LF 2407a的CAN总线接口等。
The design includes designs of different can controllers for different data nodes, the can module controlled by single chip computer and can bus interface based on DSP TMS320LF2407A, etc.
控制系统采用模块化设计，主要模块包括：控制核心CPU模块、存储器模块、调试接口模块、数据传输模块、人机交互模块、电机控制模块。
The control system is designed by module, which includes CPU core module, memory modules, debugging interface modules, data transmission module, human interface module, and electrical control module.
按照微型化、模块化的设计原则，适配器分为命令的传输解析模块、逻辑控制模块和存储模块；与上位机通信采用以太网接口。
According to the design principles of miniaturization and modularization, adaptor includes command transmission and analysis module, logical control module and memory module.
预留远程监测、远程控制模块，风管接口模块，可根据需要选装。
Reserved for remote monitoring, remote control module, the wind pipe interface module can be optional according to need.
MDIO接口模块为以太网接口芯片中MAC层对PHY器件的控制管理接口。
MDIO interface module block is an interface that is used in MAC level to control and manage PHY devices.
中间业务平台由安全控制模块、报文格式处理模块、交易控制模块、系统管理模块和核心业务系统接口模块六部分构成。
Integrate Agent system is composed of security control module, data format conversion module, transaction control module, system management module and Integrate Business system interface module.
硬件部分给出了S3C44B0X扩展CAN控制器SJA1000的接口原理图，和LCD显示模块的推荐接法；
The hardware partially produced S3C44B0X to expand CAN controller SJA1000 the connection schematic diagram, with LCD demonstration module recommendation connection;
硬件部分给出了S3C44B0X扩展CAN控制器SJA1000的接口原理图，和LCD显示模块的推荐接法；
The hardware partially produced S3C44B0X to expand CAN controller SJA1000 the connection schematic diagram, with LCD demonstration module recommendation connection;
应用推荐