本文提出一种修正近场天线测量中探头位置误差的方法——非线性迭代法。
A general correction technique is developed to remove probe positioning errors in the Near-field measurements of the antenna.
该文提出了一种修正平面近场测量中探头位置误差的算法，并进行了计算机模拟。
An algorithm for correcting probe position errors in planar near-field measurements is presented and simulated.
对于高频或低幅值测量﹐探头的地应接到测试电路中的适当位置。
For high frequency, or low amplitude measurement, probe ground shall be connected to appropriate points in the circuit under test.
其中的一个段落，或可能只是一个句子，被剪了下来，在原来的位置上留下了一扇窗户，让后一页上的文字探头探脑地露了出来。
A paragraph, or maybe just a sentence, has been sliced out, leaving a window in its place, with words from the next page peeping through.
对于A型生物测量探头，通过在声束定向、测量位置和声速设置等方面的设计思想，有效提高测量精度。
For an a mode biometric probe, ultrasonic beam orientation, measuring position and speed setting ensured the precision of the measurement.
探头的位置误差为可知值，由激光定位系统获得。
Probe positioning errors can be obtained with high accuracy using the laser positioning systems.
使用说明书必须包括灭菌参数，计划项目和温度探头在前提中的位置。
Operating Instructions must include parameters ofsterilization, the scheme item and position of the control probes in thechamber.
通过探测器的视频探头，确定被困人员位置及状态，具有防水性能，可在雨中便用。
Video probe through the probe to determine the location and status of people trapped, with waterproof properties, can be used in the rain.
只需通过调节杆式探头夹具上的一个大调节把手来调整探头在储罐内的位置，就能很方便地设定其测感点。
Adjusting the sensor position in the tank easily sets the sensing point. This is accomplished with a large adjustment knob on the cane-probe clamp.
同时，探头安装位置优化、信缆设计优化和探头安装工艺是实现腐蚀状态监测所急需解决之关键问题。
At the same time, to optimize probe installation position, communication cable design and probe installation technology is the key problem starving for solution to realize erosion status inspection.
装探头调整至合适位置。
故在驱动装置上增加触发式位置检测探头用于测量缸体顶面位置。
Therefore we add the probe of touch system with position measure in the drive to measure the position of the top of the cylinder.
以轧辊表面的涡电流引导做为检验方式，以不同的双电线探头交替检测，再轧辊表面上移动位置并随之调整电流导电率。
Eddy current inspection is performed by the inducement of eddy currents on the roll surface by the application of an alternating current from a dual-wire differential probe.
改变标准养护箱和标准养护室温湿度控制仪探头的位置，可有效地控制标准养护箱和标准养护室中的湿度。
Change the location of detecting head of humidity control gauge in standard curing box and standard curing room so as to efficiently control humidity of standard curing box and standard curing room.
如果额头有汗水，则继续按住按钮，将测温探头从额头提起，移至耳垂后方的位置，直接接触耳垂。
If perspiration is present, continue to hold button depressed, lift probe from forehead and touch the neck just behind the ear lobe.
把各测点位置画在样板上，在测点位置钻孔以备探头伸入孔内进行测量。
Put the point position in the templates, in painting measuring position for drilling to probe stretch into the hole of the measurements.
把各测点位置画在样板上，在测点位置钻孔以备探头伸入孔内进行测量。
Put the point position in the templates, in painting measuring position for drilling to probe stretch into the hole of the measurements.
应用推荐