在应用过程中，需在纤维外部加上一层反光曾，然后通过施加电子信号来控制其振动。
This involves covering the fibres with a reflective coating, and then controlling their vibration by applying electrical signals.
文章的结论可为利用振动信号进行切削在线控制的研究提供依据。
The conclusion can provide the evidence for the in-process cutting control study using vibration signals.
振动丝黏度仪主要包括振动丝传感器、温度控制系统、压力控制系统和信号调节系统。
It was mainly composed of the (vibrating) sensor, the temperature control system, the pressure control system, and the signal adjust system.
然而，目前基于功率谱均衡的数字式随机振动控制系统只能产生高斯分布的随机振动激励信号。
However, the digital random vibration control systems currently based on power spectrum fitting can only generate random vibration exciting signals with Gaussian probability distribution.
因此对振动信号的采集和处理、系统辩识、振动和噪声控制等方面的研究变得尤为重要。
Therefore, it's important to acquire and process vibration signals, differentiate and analyze the system, control the vibration and noise.
基于DWT分析汽油机振动信号特征，提出适于实时应用的爆震控制策略。
The characteristics of the vibration signals of the gasoline engine is analyzed based on DWT and put forward the strategies for real-time control.
研究表明，应用这种方法设计的电液伺服振动台系统可以实现对周期或重复性的振动实验信号的跟踪控制。
The simulation study shows that the electro-hydraulic servo vibration bable system, designed using the method presented here, can realize tracking control to penodic vibration test signals.
然后，采用信号处理和计算机控制技术，提出了多频振动主动控制规律；
Then using the signal processing and microcomputer control techniques, a phase control law is presented to control the multi-frequence vibrations of rotors actively.
基于磁流变减振器的振动响应信号，将模糊控制方法应用于磁流变减振器的控制。
Based on the response signal of Magnetorheological (MR) fluid shock absorber, the method of fuzzy control is used on the MR fluid shock absorber control.
基于磁流变减振器的振动响应信号，将模式推理控制方法应用于汽车磁流变减振器的控制。
In light of the response signal of a magnetorheological (MR) fluid shock absorber, the pattern reasoning control method is used for the control of the MR fluid shock absorber of an automobile.
应用陷波滤波器消除了弹体弹性振动固有频率信号对控制系统的影响，给出了陷波滤波器的设计方法，仿真结果证明了设计方法的正确性。
Notch filter is applied to Smooth over the problem of elastic vibration of missile body to reduce the bad effect on the control system. This Paper gives a method for the design of notch filter.
根据加工工艺的需要， 系统采用主从控制结构，振动信号的检测、频谱分析与电解加工在整个过程中交替进行。
During the processing of the foil, the signal-collecting, the frequency-analyzing and the electrolysis-controlling should been done alternately.
研究了基于自适应控制的硅微振动陀螺仪的驱动电路设计，通过固定频率信号驱动和自适应调谐实现双驱动模态的一致性。
The drive circuitry of the silicon micromachined gyroscope based on adaptive control is investigated. The coherence of two vibratory modes is achieved utilizing adaptive tuning at a given frequency.
研究了基于自适应控制的硅微振动陀螺仪的驱动电路设计，通过固定频率信号驱动和自适应调谐实现双驱动模态的一致性。
The drive circuitry of the silicon micromachined gyroscope based on adaptive control is investigated. The coherence of two vibratory modes is achieved utilizing adaptive tuning at a given frequency.
应用推荐