环氧胶粘剂的耐蚀性能是通过测定其拉伸剪切强度来评定的。
The corrosion resistance of epoxy adhesive was assessed by its tensile shear strength.
介绍了一种高强度光敏胶拉伸剪切强度测试方法,分析了影响测试结果的几种主要因素。
An introduction to the testing method for tensile and shear strength of high strength photosensitive glue is given and the main causes that have influence on the testing result is analyzed.
研究了不同搭接接头形式,胶粘剂毛边和拉伸剪切强度的测试方法对拉伸剪切强度的影响。
The effects different joint forms, queer out and the measuring ways on tensile sheer strength are studied in the paper.
测试了热循环前后胶接试样的拉伸剪切性能、质损率和表面残余应力,观察了拉伸剪切断口形貌。
The tensile shear properties, mass loss ratio and surface residual stress of the bond samples before and after the thermal cycling were measured. The tensile shear fracture morphologies were observed.
结果表明,紫外线对CFRP与混凝土的拉伸剪切强度影响较大,防护能有效缓减CFRP与混凝土的正拉粘结性能在紫外线作用下的劣化。
The results showed that the influence of UV light on adhesive property was great, and protection can slow the deterioration of adhesive strength of CFRP and concrete.
在其生命周期中,一个组件经历一系列的转换、旋转、缩放、剪切和拉伸,最后才显示在屏幕上。
During its life cycle, a component undergoes a series of translations, rotations, scaling, shearing, and stretching before it's finally displayed on the screen.
本文是对自锁锚杆在拉伸和剪切荷载共同作用下的锚固机理进行研究。
The anchorage mechanism of the locking anchor under tension together shear loads is studied in the paper.
测定了铝合金的微型剪切试验和拉伸试验的性能参数,研究了这些性能参数之间的数量关系式。
The characteristic values of micro shear test and tensile test of alloy aluminium were determined and the quantitative expressions of these characteristic values were studied.
本文介绍纺织结构复合材料在剪切、压缩、拉伸和弯曲情况下的破坏机理,分析其特点和存在的问题,提出了发展趋向。
This paper describes the failure mechanisms based on shear, compression, tension and flexure, analyzes characteristics and problems of those models and then discusses the future trend.
离聚体的拉伸强度、搭接剪切强度和乳化性能均随顺酐化程度的提高而改善。
Tensile strength and lap shear strength increased with increasing of grafting degree due to great improvement of polarity.
测定了低温下聚氨酯硬泡沫塑料拉伸、剪切和压缩弹性模量与泡沫密度、方向以及温度的关系。
Measurements have been made to determine the relation of the tension, the compression and the shearing of PUR foam at low temperature with its density, direction and temperature.
针对岩盐这一特殊性质的岩石,进行了基本的力学特性试验,包括单轴压缩、间接拉伸及变角剪切。
Testing study is made on the basic mechanical property of thenardite salt rock, which includes uniaxial compressive, indirect tensile and Angle changed shear tests.
试验结果表明,拉伸强度表现出混杂负效应,而剪切强度表现出混杂正效应,两种强度的混杂效应都随混杂比的增大而降低。
The results show that the tensile strength presents negative hybrid effect, while shear strength presents positive hybrid effect, and their hybrid effect decreases with the hybrid ratio increasing.
如果压缩力和拉伸力足够大,使得材料的各层次间相互滑移,那么就产生了剪切力。
If the compressive and tensile forces are greater enough to make the layers of the material slide upon each other, a shearing force results.
公司拥有该行业全套生产设备,全自动30t冲压机、剪切机、卷边机、切割机、烤漆房、300 T液压拉伸机等。
The company has a full set of production equipment in the industry, 30t automatic punching machine, cutting machine, crimping machines, cutting machines, paint room, 300t hydraulic tensile machine.
用碳纤维进行了性能研究,测试了拉伸、压缩、剪切和冲击性能。
The tensile compressive shear and impact properties of carbon fibre are tested.
压力产生于拉伸,压缩,或者拖,推,扭,削之类的剪切,或者某种变形以及材料的部分形状改变。
Stress results from forces such as tension, compression, or shear that pull, push, twist, cut, or in some way deform or change the shape of a piece of material.
本文介绍了微型剪切试验与拉伸试验、断裂力学试验等参数之间的对应关系。
This paper describes the correlation between the characteristic values of the micro shear test and those of the conventional tensile, fracture mechanical tests.
本产品主要用于各种金属、非金属材料进行拉伸、压缩、弯曲及剪切等试验。
This product USES for primarily every kind of metals, nonmetal material proceeds to pull to stretch, compress, flection and shear to slice etc. experiment.
得出了在不同拉伸速度和边框长度条件下装置处于准静态时的临界剪切角,并且分析了织物试样尺寸大小对准静态范围的影响。
The critical shear Angle of quasi-static state was given under different loading speeds and frame lengths condition, and the influence of specimen size on this shear Angle range is also discussed.
结果表明,在销钉的作用下,粘性流体既发生剪切变形,又发生拉伸变形,正是这两种变形的同时存在,强化了混合效果。
The result shows that both shearing and tensile distributions in the viscous fluid exhibit under the action of the pins. The mixing effect is intensified by these concurrent strains.
为此把带有波纹的底板和腹板分别等效为正交各向异性平曲板,并通过拉伸和剪切试验得到了其两个方向的等效材料常数。
The web and flange plates with a large number of corrugations are equivalent to orthotropic curve plates and their equivalent material coefficients are obtained by stretching and shearing experiments.
经典成核理论假设气泡核的形成是在静态条件下发生的,它没有反映在口模流场中动态因素(拉伸、剪切等)对气泡成核的影响。
Because classical nucleation theory supposes that bubble formation is occurred under static state, it doesn't reflect the effects of dynamic factors on bubble nucleation, such as shear and elongation.
这可能是由于它们产生剪切形变局部化的滑移面硬化率对瞬时拉伸应力的临界比值不同之故。
Presumably, it is due to their different critical values of the ratio of slip plane hardening rate to current tensile stress for shear localization.
准静态下纤维增强复合材料在偏轴拉伸和剪切时有明显的非线性。
Nonlinear behaviour occurs when partial tension and shear are exerted on quasi-static fibre reinforced composite.
实验结果表明,该算法具有较好的不可感知性,可以有效抵抗线性拉伸攻击,并且对于剪切、旋转、噪声,滤波等攻击都具有较强的鲁棒性。
The results of experiment proved that this algorithm is invisible, can efficiently against linear stretching attack, and has better robustness to crop, rotation, noise or filter attack.
结果氟斑牙三个粘接组间的剪切粘接破坏力和拉伸粘接破坏力差异均有显著性(P< 0 .0 1)。
The adhesive remnant indices were recorded. Results There were statistically significant difference in both shear and tensile debonding force among four groups (P<0.01).
泰盛结构胶具有较强的拉伸、剪切与剥离强度,耐冲击、耐压、抗振动。
Tightsen structural adhesives have excellent tensile, shear and peel strength combined with maximum impact, stress and vibration resistance.
泰盛结构胶具有较强的拉伸、剪切与剥离强度,耐冲击、耐压、抗振动。
Tightsen structural adhesives have excellent tensile, shear and peel strength combined with maximum impact, stress and vibration resistance.
应用推荐