本文将IP业务网络系统按照功能分为三个平面承载面、信令面和业务面。
IP-based service network is divided into three planes, bearing plane, signaling plane and application plane.
虽然平面二次包络环面蜗轮副具有传动效率高、承载能力大、使用寿命长等优点，但它的应用却始终受到限制。
Although the planar double-enveloping worm gearing has advantages of high transmission efficiency, excellent load capacity, long life cycle and so on, it has been used in a limited way.
平面异型中节点以小核芯为控制单元，节点核芯区的受剪承载能力取决于小核芯区的混凝土强度、尺寸和配筋状况。
Controlled by the small core area, the anti-shear capacity of plane abnormal joints is rest with concrete strength, size and reinforcement of the small core area.
文档对数据传输协议和相关的通过S1接口建立用户平面传输承载的信令协议进行了详细的说明。
The present document specifies the standards for user data transport protocols and related signalling protocols to establish user plane transport bearers over the S1 interface.
本文研究了将楼板置于钢梁下翼缘的新型组合结构平面刚度，并和传统的将楼板置于钢梁上翼缘的结构形式的平面刚度和极限承载力作了比较。
This paper researches the plane stiffness of new composite structure for slab on the lower flange, which is compared with the traditional structure for the slab on the top flange.
从橡胶坝的薄膜内力和平面问题两个基本假设出发，阐明坝体在不同承载工况下的坝袋拉力理论。
On the basis of two fundamental assumptions: the plane strain and the film internal force, this paper states at first the DAMS bag pulling force principle of different working circumstance.
特殊设计的平面承载式传感器，专用于天车过载报警。
Planar bearing load cell designed particularly is used to alarm for travelling crane overload.
另外，通过与平面K型节点对比，得出空间节点与平面节点承载力的比值。
Moreover, through comparision of the planar K-joints, the load bearing capacity ratio of multiplanar KK-joint and planar K-joint is also obtained.
多功能混凝土空心砌块的抗压、抗折强度较大，使得多功能混凝土空心砌块砌体抗压强度、抗剪强度和平面外偏心承载力较高。
Because compression and bending strength of multi-function concrete hollow block is strong, its masonry compression strength, shearing strength and eccentric of out of the plane is much higher.
采用平面杆系单元进行结构的承载力检算，采用3D实体单元进行梁体荷载响应模拟。
Plane linkage element is used to calculate bearing capacity of the structure, and 3D solid element is used to simulate response of the beam to load.
勃郎特-维西克研究的条形基础极限承载力属于平面应变问题，采用分步叠加法，求得地基极限承载力公式。
Prandtl-Vesic of ultimate bearing capacity of strip foundation belongs to the plane strain problems, which adopt step superposition method to obtain the formula of ultimate bearing capacity.
不同螺旋槽平面型线对螺旋槽推力轴承的压力场及承载能力会产生不同程度的影响。
Different influences on the pressure fields and the loading capacity of spiral groove thrust bearings are produced by different groove molded lines.
本文利用ANSYS有限元程序通过正交设计的方法对格构式斜腿刚架进行了平面外整体稳定承载力参数分析，得到显著影响因素。
By means of the finite element program ANSYS and using orthogonal design method, the parameters having effect on the stability of this structure were analyzed and primary factors were obtained.
根据三个平面理论，话题是个语用成分，指述说的对象。它在语句线性序列中的位置分布及其形式都与它所承载的信息内容密切相关。
According to the Three-dimension Theory, a topic is a pragmatic element, and it refers to a person or thing that is being talked about.
控制平面和转发平面是虚拟路由器的两个基本功能平面，分别承载逻辑控制平面和逻辑转发平面。
Control plane and forwarding plane were two basic function planes in virtual router, correspondingly carrying logical control plane and logical forwarding plane.
利用ANSYS软件分析了输电铁塔鸭嘴形横担上平面的两种布材形式分别对其整体稳定极限承载力的影响。
The influence of 2 X-crossing arrangements for the upper plane on the ultimate bearing capacity of duck bill cross arm in the transmission tower are analyzed by ANSYS in this paper.
考虑两种基本荷载组合，在对平面屈曲约束支撑钢框架结构整体可靠度评价的基础上，给出了在一定目标可靠度下的基于结构体系极限承载力可靠度的实用设计公式。
Considering two basic types of load combinations, the practical design method was proposed to achieve a target reliability index of the system resistance based on the assessment of system reliability.
在结构计算中验算壁板、墙肢平面外承载能力，是井塔有别于一般高层建筑结构的特殊要求。
Different from ordinary highrise structures, it is required to check the out of plan endurability of wall in structure analysis of wind tower.
在结构计算中验算壁板、墙肢平面外承载能力，是井塔有别于一般高层建筑结构的特殊要求。
Different from ordinary highrise structures, it is required to check the out of plan endurability of wall in structure analysis of wind tower.
应用推荐