属机械法对中心，可以磨削中等精度光学零件的外圆或端面。
The center is a mechanical method, can moderate precision grinding of optical parts of the cylindrical or end.
或为设在电机壳体侧壁或端面上对应于轴承部位的圆形或方形注油孔。
Alternatively, the oil injection hole is the round or square oil injection hole which is arranged at the positions of the side wall or end surface of the motor shell corresponding to the bearing.
在端面车削操作中，进给由横向滑板提供，而切削深度则通过大拖板或复式刀架控制。
During a facing operation, feed is provided by the cross slide, whereas the depth of cut is controlled by the carriage or compound rest.
设备口法兰的类型、等级及端面应符合买方图纸或数据表的规定。
The type, rating and facing of nozzle flanges shall conform to those specified in Purchaser's drawing or data sheet.
事实上，此次影响的极端面兴许会使得你与一位密友或恋人渐行渐远。
In fact, the extremist nature of the influence may actually find you even further divided from a close friend or lover.
如此办法不能控制漏料，则可能是石墨垫或铜环磨损较严重(如密封端面不光滑，间隙大)。
So the means cannot control leak the material, then possibly is the graphite pad or the copper collar wears (for example seal face not to be smooth seriously, gap big).
轴承内孔或外表面与套圈一端面连接的套圈表面。
Bearing bore or outside the surface and the ferrule end face connected to a ring surface.
如指定使用外螺纹及内螺纹或榫面及槽面法兰，容器设备口法兰端面应为凹槽型。
When male and female (M&F) or tongue and groove (T&G) type flanges are specified, the nozzle flange facing of the vessel shall be of female or groove type.
垂直于轴心线的平面，与套圈基准端面或垫圈背面的切面平行的平面，可以认为是径向平面。
The plane perpendicular to the axis line, and the ring reference face or back of the section parallel to the ring plane, can be considered a radial plane.
端面热电偶适合于测量电厂汽轮机及电机轴瓦或其他机体的表面温度。
End surface thermocouple suitable for measuring steam turbine power plants and motor bush or other body surface temperature.
铣削端面时，为了将工件送到刀具底下或下方，工作台可以纵向移动。
When face milling is performed, the table can be moved longitudinally to feed the workpiece under or below the cutter.
与套圈基准端面或垫圈背面的切面垂直的方向，可以认为是轴向。
With the ring or washer on the back of the base face the direction of the vertical section can be considered...
与套圈基准端面或垫圈背面的切面垂直的方向，可以认为是轴向。
With the ring or washer on the back of the base face the direction of the vertical section can be considered to...
分析中，对每种密封端面，其结构参数都是依据有关文献选取的优化或近似优化的数据。
In the analysis, the geometric parameters for each face configuration, which are taken from relevant references, are optimal or approximately optimal data.
结果表明，轴承内圈端面上的缺陷由夹杂物或夹渣所致，为冶金缺陷。
The results showed that the defects on the inner ring of the bearing are hair-cracking causing by serious impurities or slag enclosures, these are metallurgy defects.
但也可按照产品图纸要求标在护罩、保持架、挡圈，密封或防尘装置的端面上。
But can also be marked in accordance with the requirements of Product drawings at guard and maintain the planes, ring, seal, or device-side surface dust.
下表面层外端面上设有一层纸或塑料膜，并通过不干胶与下表面层贴合在一起。
The external end-surface of the lower layer is provided with a paper layer or a plastic film which is bound together with the lower surface layer through the non-setting adhesive.
它是用淀粉加工而成的条状物，其特征是粉丝长度为2-10毫米，两端面为规则或不规则的圆形或长方形。
The utility model is a stick made of starch. The utility model is characterized in that: the length of the vermicelli is 2-10mm. Two end faces are regularly or irregularly circular or rectangular.
初步解决了在相同或不同转速下，两条端面曲线啮合的条件。
Also, the solution to the intermeshing condition of the two cross section curves under either same or different speeds is provided. Cross section curves for practical instants are plotted.
端面刀具用在端面作业中加工平板侧面或端部表面，也有加工左右侧表面之分。
Facing tools. Facing tools are employed in facing operations for machining plane side or end surfaces. There are tools for machining left-hand-side surfaces and tools for right-hand-side surfaces.
端面刀具用在端面作业中加工平板侧面或端部表面，也有加工左右侧表面之分。
Facing tools. Facing tools are employed in facing operations for machining plane side or end surfaces. There are tools for machining left-hand-side surfaces and tools for right-hand-side surfaces.
应用推荐