在相同成型压力下，坯体的密度增高；
成型压力对反应浸渗材料的强度影响不大。
The forming pressure has no obvious effect on the bending strength of the composite.
随着磁粉粒度及成型压力的增大，磁粉芯的磁导率增大。
Increasing the granularity of magnetic powder and shaping pressure can increase the permeability of magnetic powder core.
随着成型压力的增加，板材的静曲强度和弹性模量都上升。
The board's MOR and MOE rise with the increasement of molding pressure.
炭膜的分离性能与成型压力、粘结剂含量等工艺条件有关。
Separation properties of carbon membrane were affected by binder ratio, moulding pressure etc.
往复螺旋注射成型机把压出机和成型压力机的功能结合起来。
A reciprocating screw injection molding machine combines the functions of an extruder and a compressive molding press.
着重研究了粉末粒度与成型压力对钨铜材料烧结致密度的影响。
The influence of powder grain size and forming pressure are discussed for the performance of W-Cu composites.
研究成型压力对蒸压灰砂砖抗压强度和耐盐酸腐蚀能力的影响。
In this paper, the effect of molding pressure on the strength and hydrochloric acid stability of autoclaved lime_stone sand brick is studied.
其成型工艺参数包括冷却速度、成型压力、成型温度、保温时间。
The processing parameters of PEEK composites include cooling rate, forming pressure, forming temperature and the holding time in melt.
本课题的研究对加快我国医用成型压力绷带的推广与应用将起到积极作用。
The research of this subject will play a positive role in enhancing the popularization and the application of the medical shaping pressure bandage in our country.
考察了粉末粒度、粘结剂含量、成型压力、磁场等对粘结磁体性能的影响。
The influence of particle size, content of epoxy adhesives, molding pressure and aligning field on the properties of bonded magnets is investigated.
研究了PTFE废料粒径、各种填料用量及预成型压力对产品性能的影响。
The influence of granule size of waste PTFE, mass ratio of fillers and the preforming pressure to the performance of the product is studied.
分析了影响成型特性的因素，如煤种、粒度、水分、成型压力和成型率等。
Analyses are made for the influence factors of moulding characteristics such as coal type, size, distribution water content, moulding pressure and briquetting rate.
由于瘠性料的抗压强度高于塑性料，从而导致瘠性料的成型压力高于塑性料。
The densification molding pressure of hard brittle material is higher than that of plastic material because of the higher compression strength of hard brittle material.
探讨了烧成温度、保温时间、成型压力等工艺因素对于该复合材料性能的影响。
Effects of heating temperature and duration, shaping pressure etc. on the properties of this glass composite have been discussed.
复合材料的成型条件如成型时间、成型压力、成型温度等影响基体的浸渍程度。
The processing conditions of forming composites such as time, pressure and temperature influence the matrix's impregnating degree.
随着成型压力的增大，多孔钛孔隙尺寸和孔隙度减小，但孔隙形状未发生显著变化。
The increasing in forming pressure reduces the pore size and porosity, but has little effect on the pore shape.
研究了反应烧结碳化硅陶瓷的显微组织和性能与生坯碳含量、成型压力以及碳粉粒度的关系。
The effects of carbon content, moulding pressure, and carbon particle size of green body on microstructure and properties of reaction-bonded silicon carbide (RBSC) have been investigated.
研究了配料组成和前驱体成型压力对多孔碳板的气体透过性能、孔隙率、和电导率等指标影响。
The effects of composition and pressure of its precursor on the properties, such as gas permeability, porosity, and electric resistivity, were studied.
不适当的成型压力的维持时间会破坏“压力回弹”作用，造成催化剂成型体的机械强度明显降低。
The "rebound effect" will be undermined by the unsuitable pressure maintain process, resulting in the apparent decrease of mechanical strength of catalyst pellets.
指出了粉煤可压缩性是影响其成型特性的主要因素之一，也是型煤生产中选择成型压力的重要依据。
It is pointed out that the compressibility of fine coal is not only one of main factors influencing the briquettability of fine coal but also important basis selected br.
研究了成型方法、原料配比、成型压力、练泥遍数及烧成制度等工艺条件对多孔透水砖性能的影响。
The effect of the technological conditions such as molding method, raw material proportioning, pugging times and sintering system on the performances of porous permeable bricks was studied.
影响阳极基底与YSZ电解质薄膜共焙烧匹配性的主要因素是成型压力、预焙烧温度和焙烧升温速率。
Molding pressure, Sinter temperature in advance and the velocity of temperature raised are the main factors for the matching of anode substrate and thin film YSZ electrolyte.
该工艺通过向气囊内充压，对预成型体施加一定的成型压力，从而提高构件纤维体积含量及力学性能。
This process can add mould pressure to the preforms through inflating the bladder. Thus, higher fiber volume fraction can be achieved.
影响阳极基底与YS Z电解质薄膜共焙烧匹配性的主要因素是成型压力、预焙烧温度和焙烧升温速率。
Molding pressure, sinter temperature in advance and the raise velocity of temperature were the main influencing factors for the matching of anode substrate and thin film YSZ electrolyte.
研究了生物质配入量、肥煤配入量、成型压力、 煤料筛分组成、炭化加热速度对型焦抗压强度的影响。
The effect of additive amount of biomass and fat coal, briquetting pressure, coal sizes distribution, heating velocity of the carbonization process on the strength of formed coke were examined.
对影响产品性能的几个重要因素，包括胶凝材料用量、成型压力、物料含水率和养护制度等进行了研究探讨。
The important factors influencing the product performance are investigated, including the dosage of cementing agent, forming pressure, material moisture and curing regime.
随成型压力的增加，当保压一定时间、添加一定量助烧剂时，生坯密度随之增加，饱和磁化强度也相应提高。
With the increase of molding pressure, holding pressure for certain time and adding a certain amount of boric acid doping, the compact density and saturation magnetization correspondingly increase.
结果表明，在旧预成型模具的基础上改进的新型模具能精确控制预成型压力，从而可以保证预成型体的尺寸精度和质量。
The results showed that the new perform mold made from the old mold could control the pressure of the perform, so that the perform could have exact dimension and good quality.
结果表明，在旧预成型模具的基础上改进的新型模具能精确控制预成型压力，从而可以保证预成型体的尺寸精度和质量。
The results showed that the new perform mold made from the old mold could control the pressure of the perform, so that the perform could have exact dimension and good quality.
应用推荐