通常，必须在某一总线主控PC I扩展槽中拥有驱动器适配器。
In general, must be in a PCI bus master expansion slot has a drive adapter.
操作：将适配器安装在具有总线主控能力的插槽。查阅计算机文档以了解详细信息。
ACTION: Install the adapter in a bus mastering-capable slot. See your computer documentation for details.
CAN子网由一个主控制器协调，该主控制器也为主CAN总线提供网关。
The CAN subnets are coordinated by a master controller that also provides the gateway to the main CAN bus.
介绍了一种基于CAN总线的可扩展的嵌入式温度监测系统的设计方法，整个系统由嵌入式分控器和主控器两大部分组成。
This paper introduces a design of embedded temperature monitoring system which is based on CAN bus, the entire system composes by the embedded controller sub-master and the Master controller.
文章还阐述了基于CAN总线传输温度信号的主控器系统的设计方法。
And it also elaborates the design of the transmission temperature of the master signal system which is based on CAN bus.
单片机通过CAN总线向主控制器发送检测数据，主控制器经过判断可主动启动并完成车体的制动动作。
The microcontrollers transmit data to the main controller by the CAN bus, the main controller can start-up and finish the brake action initiatively after estimating.
硬件分为上层主控板和下层数据采集板，采用基于CAN总线的分布式设计。
Hardware including the upper control board and the underlying data acquisition board, used distributed design based on CAN bus.
本设计实现了在MIC总线冗余系统中主控制器与从控制器间的数据通讯。
This design realizes the data communication between the main controller and accessary controller in MIC bus redundancy system.
主控计算机与各lcu中的监控单元和保护单元通过CAN总线通信，LCU中的PLC通过RS- 485接口与主控计算机通信。
Host computer communicates with the monitor unit and the protection unit of LCUs through the CAN bus. PLC in LCU communicates with host computer through the RS-485 port.
同时采用CAN总线通讯取代通常的串口通讯，使主控器能更好的实现实时响应功能。
The communication of CAN bus replaces the string communication, making the main controller of the elevator control system better realtime response ability.
本地主控机通过RS485总线向现场信号采集设备发送控制指令并接收采集的测试数据，从而实现对rs485总线通信的控制。
The local controller sends steering order to field signal-acquisition equipments and receives test data from RS485 bus, thereby communication control of RS485 bus was realized.
AHB总线接口设计划分为主控模块接口设计及从模块接口设计。
As the basic SoC design technique, the AHB bus interface design consists of master module interface design and slave module interface design.
采用了RS485和CAN总线接口，实现了电子送经卷取控制系统和织机主控制系统之间的通讯。
The electronic let-off and electronic take-up system USES RS485 and CAN BUS to communicate with the main control system of a loom.
在介绍了传统测试系统的基础上，描述了一种基于USB总线的FPGA主控多功能测试系统。
Based on introduction of traditional measurement system, a multi-function measurement system controlled by FPGA based on USB bus was described.
将CAN现场总线技术应用到控制现场底层设备与主控IPC的通讯，实现测控信息处理的现场化。
The CAN Field Bus causes the information to be processed in control field and realize the communication between the control field equipment and the host IPC.
各个节点设计上采用内置CAN模块的飞思卡尔16位单片机作为主控芯片来搭建硬件电路，以实现CAN总线的物理层和数据链路层。
Through using 16-bit freescale MCU embedded CAN controller as master chip in each node, it achieved the design of hardware circuit, so realized CAN physical layer and CAN data link layer.
USB技术在嵌入式系统中有两种主要的应用方式：即作为USB总线设备的USB设备方式和作为USB主控制器的嵌入式USB主机。
There are generally two modes of USB technology could be used in embedded systems, one is the USB device mode using as USB Devices and the other is USB host mode using as USB Host Controllers.
在硬件设计上，主控系统、插补和补偿模块以及伺服模块通过CAN总线互连，实现嵌入式数控系统硬件的可重构性。
In the system, the main control module, the interpolation and compensation module and the servo module are attached with CAN bus, which achieves the reconfiguration of the hardware.
该有限状态机作为主控制模块的核心，主要用于完成控制MTM总线的消息传送顺序；
The FSM is the core of master module, it controls the transmission of the messages on the MTM bus.
固定信息站通过CAN总线把位置信息上传到井上主控PC机，在PC机上进行处理并在电子地图上显示出来。
The BS will send these information to main control PC computer on the ground through CAN bus, and the PC processes the data to get the MS location and displays it on the electronic map.
固定信息站通过CAN总线把位置信息上传到井上主控PC机，在PC机上进行处理并在电子地图上显示出来。
The BS will send these information to main control PC computer on the ground through CAN bus, and the PC processes the data to get the MS location and displays it on the electronic map.
应用推荐