为了把高粘性尾煤泥滤饼制备成水煤浆，研制了循环剪切桶和剪切泵。
The circulation shear bucket and shear pump were developed for treated the high stick slime cake.
通过将界面粗糙度定义为等效起伏角，模型能模拟节理循环剪切性状。
After the joint roughness is defined as the equivalent inclination Angle, the model can simulate the behaviors of joints under cyclic loading.
动强度曲线显示循环应力比与循环剪切破坏次数的对数基本呈直线关系。
The dynamic strength curve indicates that there is basically a linear relationship between the cyclic stress ratio and the logarithm of the cyclic number required at failure.
考虑到天然黏土不等向固结历史的影响，试验土样在循环剪切前均先K0固结至原位应力状态。
Taking the stress-induced anisotropy into account, all the specimens are initially restored to the in-situ stress state under K0 consolidation.
在早期版本的Modeler中，您必须剪切和粘贴才能将任务移动到循环中。
In previous versions of Modeler, you had to cut and paste to move tasks into a loop.
污水残渣经过刀组的剪切，并且多次循环，被粉碎成细小颗粒的污泥残渣。
Sewage residue after shear knife, and recycled many times, was crushed into fine particles of sludge residue.
基于剪切筒模型和常用疲劳加载方式，首先建立了循环荷载作用下钢筋与混凝土界面脱粘应力的计算模型；
Based on the shear-lag model and the usual loading way, the computation model of interfacial debonding stress under tension-tension cyclic loading is established first.
文件可以被被正确地剪切并导出以创建一个的循环。
Files can be accurately cropped and exported to create a perfect loop.
液化面作为累积剪切功的函数，从初始应力点的包络线开始，随着循环活动性的进行，逐渐接近破坏线。
The liquefaction front, originating from the envelope of initial effective stress points, gradually approaches the failure line as the cyclic mobility proceeds as a function of plastic shear work.
采用新型密封材料——艾志黑色CMS2000层状剪切式软填料对离心式循环水泵填料密封进行了技术改造。
New type sealing material CMS2000 packing layer shearing soft sealing material to technically improve the filler seal of centrifugal circulation water pumps.
感应各向异性，剪胀，剪切软化和循环流动的机制，从微观机制的观点出发，进行了讨论。
The mechanism of induced anisotropy, dilatancy, shear softening and cyclic mobility was discussed from the viewpoint of micro-mechanism.
在高速水流循环系统中，用自行研制的剪切力传感器分别量测了清水、掺气水流及挟沙水流壁面上的剪切力；
In a special circulating system with high velocity flow, boundary shear stresses in clear water flow, aerated flow and sediment laden flow are measured.
该仪器工作原理是将样品被循环引入高速相对运动的定转子间的狭小空间，并被快速剪切和破碎。
Its working principle is making the sample circularly loop into a narrow space between the high speed and relative motion stator to shear and break the sample.
测试了热循环前后胶接试样的拉伸剪切性能、质损率和表面残余应力，观察了拉伸剪切断口形貌。
The tensile shear properties, mass loss ratio and surface residual stress of the bond samples before and after the thermal cycling were measured. The tensile shear fracture morphologies were observed.
当土体剪切面为不规则剪切带时，施加循环荷载后出现残余强度上升的现象。
When shear surfaces are irregular shear bands, residual strengths increase after applying cyclic loads.
利用改进的循环单剪试验系统进行粉质黏土—混凝土接触面剪切性能试验。
The simple shear tests are conducted to study the shear properties of silty clay-concrete interface by using the improved cyclic simple shear testing system.
结果表明，一定时间的热循环会造成LF6铝合金焊接接头断裂机理的改变，由未经热循环时的纯剪切型断裂，逐渐过渡成微孔聚集型断裂。
The results show a certain time thermal cycle can cause the fracture mechanism change. It varies from original pure shear fracture to microvoid coalescence fracture gradually.
结果表明，一定时间的热循环会造成LF6铝合金焊接接头断裂机理的改变，由未经热循环时的纯剪切型断裂，逐渐过渡成微孔聚集型断裂。
The results show a certain time thermal cycle can cause the fracture mechanism change. It varies from original pure shear fracture to microvoid coalescence fracture gradually.
应用推荐