考察了反应温度、反应时间和催化剂的用量等对反应结果的影响，得到最佳工艺条件。
The effects of reaction temperature, reaction time, catalyst dosage etc. on the reaction were investigated and the optimum reaction process was obtained.
通过正交试验方法对脂化反应和超临界CO2萃取工艺进行优化，得到最佳工艺条件。
The craft of esterification reaction and supercritical CO2 extraction has been optimized through the orthogonal experimental technique and we have obtained the best craft condition.
通过熔点测定、质谱和气相色谱分析等手段对产物进行了结构表征和含量分析，并研究得到最佳工艺条件。
The structure was confirmed by melt point and MS with the content being analyzed by GC , and the optimum technological condition was determined.
通过正交试验法得到最佳工艺条件，研制后的成品无论从体积、形状、色泽、质感和营养成分上均有明显的提高。
The optimum technological condition has been obtained through testing. The cooked dish has obvious improvement in volume, shape, colour, texture and nutrient.
得到了生产球形活性炭的最佳工艺条件，生产的球形活性炭达到了净化用颗粒活性炭的质量标准。
The optimum technological conditions for producing the globular activated carbon have been obtained, and the produced globular activated carbon has reached the quality standard for purification.
为了得到薄膜的最佳沉积工艺条件，本文给出了检验碲化铅材料性质的简便方法。
In order to obtain an optimum deposition condition a simple method to test PbTe coating material before its deposition is suggested.
研究了合金工艺，得到了最佳合金条件。
After the study on the alloy technology, we got the good alloy conditions.
考察了物料摩尔配比、反应温度和反应时间对反应的影响，得到了最佳工艺条件。
Investigated molar ratio, reaction temperature and reaction time on the reaction, the optimal process conditions.
利用正交实验得到了反应的最佳工艺条件。
The optimum conditions were attained by the orthogonal experiment.
实验中，通过改变反应的进料速度，可以得到不同反应条件下的实验数据，可以得到反应温度下的最佳工艺条件。
By changing the speed of incoming materials of reactions, the experimental datas dissective to get the best process conditions are obtained in a different reaction condition.
通过试验得到了最佳工艺条件，同时对其增强机理进行了探讨，结果表明此接枝壳聚糖共聚物有良好的增强作用。
Through the study, the optimum technical parameter was obtained, and it was also proved the chitosan copolymer had good strengthening effect on fibers.
最终得到移动磁场下铸造ZL 102薄壁件的最佳工艺条件为：不锈钢底模，电压为220v- 235v。
Under traveling magnetic field, casting ZL102 aluminum alloy thin-section castings' best process is: using stainless steel as bottom mold, voltage is between 220v-235v.
本文采用低温结晶法，选择最佳工艺条件，得到理想产率的不饱和脂肪酸。
Applying the crystallizing process under low temperature and selecting the optimum technology condition, the paper successively abstracted unsaturated fatty acid with real recovery.
研究得到氧化锂真空还原的最佳工艺条件。
The optimum technical conditions to reduce Li2O under vacuum were gained.
研究了以籼米为基质的脂肪替代品加工过程中的酶水解工艺，采用响应面分析法得到了最佳酶解工艺条件，并对不同干燥工艺进行了比较。
The enzymatic hydrolysis in the process of long rice based fat substitute was studied and the optimal conditions of the enzymatic hydrolysis was obtained by using Response Surface Analysis.
同时考察了乙酸酐与苯酚物质的量比对苯酚转化率的影响，得到了合成乙酸苯酯的最佳工艺条件。
Meanwhile, the influence of the ratio between phenyl hydroxide and acetic anhydride to translating rate was also studied, and the optimum technological condition…
纳米氧化镁经月桂酸钠处理可以得到表面亲油化的粒子，改性最佳工艺条件为：改性温度600C；
The optimum processing conditions in the surface modification of nanometer magnesia : the modification temperature is 600C;
通过实验得到了合成的最佳工艺条件。
The optimum reaction conditions were obtained by experiments.
考察了温度、硫酸浓度、时间等因素对反应的影响，得到了最佳工艺条件。
The influences of temperature, concentration of sulfuric acid and time on the reaction were studied. The optimum conditions of reaction were obtained.
同时，得到了毫秒2 ~15段的最佳工艺条件。
At the same time, the proper process conditions of 2 ~ 15ms delay com...
本文考察了萃取剂浓度、用量、反应温度、分散用水量等因素对对氯苯甲酸离解萃取过程的影响，得到了最佳的分离工艺条件。
In this study, base and acid were used for extraction, and the amount and concentration of extraction, temperature and the amount of water as scatter were investigated during the process oft...
对垂直腔面发射激光器的湿法腐蚀技术、选择氧化工艺、合金工艺等关键工艺进行了研究，得到了最佳工艺条件。
We have explored technologies for the fabrication of VCSELs, such as wet etching, wet and selective oxidation and annealing.
通过正交实验得到了瓷质氧化的最佳工艺条件，并对氧化膜的防护性能、氧化液主要成分的消耗速度进行了测定。
The optimal technical condition is determined by the method of orthogonal layout. Corrosion resistant performance and depletion of potassium …
在最佳工艺条件下反应得到蔗糖多酯产率达到89.12%，酯化度6.8。
Under the optimum conditions the sucrose polyester (SPE) yield attained 89.12%, and the esterification degree reached 6.8.
在最佳工艺条件下反应得到蔗糖多酯产率达到89.12%，酯化度6.8。
Under the optimum conditions the sucrose polyester (SPE) yield attained 89.12%, and the esterification degree reached 6.8.
应用推荐