运用算例分析了有关参数对泵筒径向变形的影响。
By examples, the effect of relative parameters on the radial deformation is analyzed.
分析活塞环弹流润滑性能时考虑气缸套径向变形的影响是非常必要的。
An elliptical cylinder model was built to analyze the effects of cylinder liner radial deformation on the elastohydrodynamic lubrication performances of piston ring.
此外，为了提高活塞环润滑性能应尽量减少气缸套和活塞环的径向变形量。
Also, the radial deformation of cylinder liner and piston ring should be reduced to improve the lubrication performances of piston ring.
圆柱形壳体与法兰对接环形焊缝将引起壳体的径向变形及法兰平面度的变化；
The changes of the radial deformation and the flange's planeness are induced by the circumferential weld at the joint between the cylindrical shell and the flange ;
结果表明：缸体的径向变形是轴向位置的函数，半径方向的应力是径向位置的函数。
The results show that the radial deformation is the function of axial position and radial stress is the function of radial position.
截止阀的柔性元件的径向变形值可以调节，保证柔性螺纹套的环槽与螺杆上的螺纹的接合深度。
Radial distortion of the flexible component in the stop valve can be adjusted so as to ensure the joint depth between flexible screw thread trepanning circular groove and screw thread on the screw.
分析结果表明：热变形是单齿转子压缩机转子变形的主要因素，转子的铸造空腔结构导致转子径向变形很不均匀。
It is shown that thermal deformation is the dominant influencing factor, and that the casting cavity of the rotor results in the serve non-uniform of redial deformation.
分析表明：强力旋压毛坯件的变形流动主要是轴向变形，影响成形质量的因素主要是成形过程中的径向变形和切向变形。
The results indicate that the deformation flow of power spinning is mainly axial deformation, the radial deformation and circumferential deformation have an impact on the forming quality.
以300MW汽轮机组为对象，对高压内缸进行几种典型工况的分析计算，得出了高压内缸在不同工况下的径向变形趋势并分析了变形原因。
Based on the 300mw unit, calculations of high pressure inner cylinder on different typical conditions are carried out, and the deformation trends are concluded.
当膜力卸除后，周向弹性变形和径向缩短的弹性变形导致回弹。
When the membrane stress is removed, circle elasticity deformation end radial shorten elasticity deformation make for resilience.
采用高斯径向基函数和一阶剪切变形理论对普通复合材料叠合板的固有频率进行了计算。
The Gaussian radial basis functions and first-order shear deformation theory are presented to calculate the natural frequencies of generally laminated composite plates.
利用上限元法(UBET)模拟了圆柱直齿轮径向挤压过程的变形力规律。
Laws of the deformation force during radial extrusion of spur gear are simulated by using UBET.
EMP径向滑动轴承的热弹变形对轴承的润滑性能影响较大。
The thermal-elastic deformation of EMP radial sliding bearing makes rather big influence on lubrication properties of bearing.
径向锻造可获得全截面细晶材料，并实现高合金难变形材料由锭到材的一火次锻造。
The gross section fine grain material can be obtained by radial forging. One heat forging from ingot to finished products of high alloy with hard deformation can be realized.
在径向未变形切屑厚度公式的推导中，考虑了刀具进给运动的三维特点。
The three dimensional characteristic of cutter feed motion is considered in the formulation of undeformed radial chip thickness.
与滚动体及滚道的总永久变形量相对应的径向静负荷（中心轴向静负荷）。
Raceway and rolling body and the total permanent deformation of the corresponding radial static load (center of the axial static load).
通过静态结构分析，得到挡轮液压缸在径向载荷作用下的变形和应力分布状况；
The deformation and stress distribution of the cylinder under radial force are obtained by static structure analysis.
其次，由轴向定位预紧轴承受径向载荷时各滚子的变形，推导出轴承的径向刚度计算公式；
Second, the calculation formula of radial rigidity is deduced according to the deformation of rollers under the radial load with axial position preload.
装轴承的孔不圆，也会使轴承外环变形而引起主轴径向圆跳动。
Not loaded bearing a round hole, there will be outer bearing spindle radial deformation caused by a round beating.
当测量直径公差时，记得的径向轴承在研磨后可能产生微小变形。
When determining the diameter tolerances, remember that thin-walled rings of radial bearings may become slightly deformed after grinding.
在轴承与主轴支撑面的径向位置上设有的热膨胀量和弹性变形余地。
The radial position between the bearing and the supporting surface of the main axis is provided with a space for the heat inflation and the springy transformation.
本文研究了圆锯片径向槽的数量、长度、宽度对圆锯片热变形的影响。
The effects of the number, length and width of the slots on the thermal deformation of a circular sawblade were investigated in this paper.
采用三维刚塑性有限元法对四种径向精锻变形道次的变形分布进行了数值模拟计算；
The strain distributions of four kinds of radial forging processes have been simulated by rigid-plastic FEM.
研究结果表明，与传统压边方法相比，采用径向分块压边方法可以对径向不同变形质点分别压边，有效提高拉深成形极限，并获得更好的压边效果。
The results for forming process of cylindrical parts show that it can carry out blank holding for different radial deformation zones by radial segmental blank-holder technique.
开花时，花药壁由表皮和几层薄壁细胞以及径向壁纤维加厚的变形细胞组成。
At anthesis, the mature anther wall included epidermis and some layers of parenchymal cells and several layers of endothecium cells with an evidently thickened radial wall.
活塞环在运行状态下由于存在温度梯度而发生变形，导致活塞环开口附近接触状况变化和径向压力增加。
During the Operation of the engine the temperature graduate is likely to deform the piston ring, as may alter the contact situation at the opening of the piston ring and raise the radial pressure.
本文提出了一种新型的变形体镗头方案，在该方案中，压电陶瓷驱动柔性铰链机构实现镗刀的径向进给。
This thesis puts forward a new solution of deformed boring-head, in which piezoelectric drives flexible hinge mechanism to realize radical feed.
指出带卷径向存在温度梯度，在冷却初始阶段冷缩变形不均匀是产生粘结的主要原因。
It observes that there is diametral temperature stairs to the coil and the main reason that the coherence occurs is due to the uneven shrink of the coil at the beginning of the cooling phase.
镦粗加工过程是将金属变形于纵向和径向使其截面积增大。
Upsetting. Upsetting is the process of increasing the cross sectional area by displacement of material longitudinally and radially.
根据检测结果用径向基函数插值方法将事先选择好的一个中性标准网格模型进行空间网格变形使其变形为个性化人脸几何模型；
Thirdly we employ radial basis functions (RBF) interpolation method to deform a neutral generic model to the personalized geometry model according to the detected features.
应用推荐