对试件进行预制冲击损伤试验和冲击形貌分析。
Impact damage was prefabricated on the specimen and the form of specimen after impact was analyzed.
利用AF M对纤维表面形貌分析的结果与XPS结论一致。
The fiber surface morphology analysed by AFM also approved the result of XPS analysis.
由磨面形貌分析可知强化层是以塑性变形引起的犁沟方式磨损的。
The worn surface morphology analysis shows that the wear of laser strengthened layers follows the plough trenches way caused by plastic deformation.
结果对比表明，这种W - M函数可用于微镜表面的建模和形貌分析。
The result shows that the W-M function is efficient in creating models and analyzing the topography of MEMS surface.
结合拉伸断口形貌分析，讨论影响铅基复合材料拉伸断裂过程的主要因素。
The main factor which affects on the tensile fracture of the C/Pb composites was given.
利用扫描电镜和电子能谱，进行了纤维表面形貌分析及表面活性官能团分析。
The micro morphology of fiber surface was analyzed by SEM, and the active functional group on the fiber's surface was analyzed by XPS.
AF M形貌分析表明陶瓷支撑体上的二氧化硅薄膜连续，膜表面较光滑、平整。
AFM image shows that the silica membrane on the ceramic support is continuous and the surface is relatively even and smooth.
通过磨屑形貌分析和对磨损表面的观察与分析所得的关于复合材料的磨损机制的结论是一致的。
The conclusion on the wear mechanism of the composite by the debris topography analysis is coincident to that of the SEM analysis on the worn surface.
用扫描电镜进行的冲击断面形貌分析表明，共混体的增韧机理以剪切屈服为主兼有多重银纹化。
It was found from the analysis of the impact cross section on SEM that the toughening mechanism was mainly the shear yielding with some degree of multiple crazings.
采用冲击试验和断口形貌分析对经不同温度时效处理后的AZ80镁合金冲击性能进行了分析。
The impact test and SEM fracture analysis were carried on for AZ80 magnesium alloy after different temperature ageing, and the effects of ageing on impact property were investigated.
对一个实际清淤中磨损失效的泥浆泵轮叶片表面进行宏观观察，并利用扫描电镜作了微观形貌分析。
The abrasive erosion pattern of the impeller blades of a used slurry pump is investigated by macro observation, and analyzed by SEM method.
本文试就低速大扭矩液压马达(YMA- 2500)运转中定子的失效情况进行了宏观形貌分析。
Here in described the macroscopic analysis for the failure of stator which located in low speed with large torque hydraulic motor (motor type YMA-25000).
采用扫描电子显微镜对膜层进行了形貌分析，并对氧化处理前后样品的耐磨性和耐蚀性进行了测试分析。
SEM (scanning electronic microscope) was adopted to observe the morphologies of the oxidized alloys. The wear resistance and corrosion resistance property were assessed.
报导了以SEM为表征手段，对重铬酸盐钝化处理的黄铜制品进行了表面形貌分析，就其防腐性能进行了测试。
In this paper, the surface characterization of the brass inactivated by dichromates is analyzed by SEM, and its anticorrosion property is tested.
通过力学性能和耐磨性能测试、金相组织观察和ESEM形貌分析，研究了氮含量对低碳高铬铸铁性能的影响。
The effects of nitrogen on the properties of low carbon high chromium cast iron were studied by mechanical property and wear resistance test, and metallograph analysis using OM and ESEM.
通过拉伸力学性能测试和断口形貌分析，研究了2195铝锂合金冷轧薄板的各向异性随时效时间变化的规律。
The anisotropy during aging treatment for 2195 Al-Li alloy cold-rolling sheet is studied through tensile mechanical properties and electron fractography.
采用宏微观形貌分析、化学成分分析、力学性能测试、SEM微观形貌分析等手段，分析了减速机轴断裂的原因。
The fracture reason of reducer shaft was analyzed by means of morphology and microstructure analysis, chemical composition analysis, mechanical properties test, SEM micro-morphology analysis.
形貌分析结果表明，因H、O原子等逸出及微晶间部分碳原子被烧损，PANACF的表面形成了极丰富的微孔。
The results show that the release of H and O atom and the burning of part carbon atoms in microcrystal, results in formation of the enrich micropores at the surface of PANACF.
通过裂纹宏微观形貌分析、腐蚀介质分析、对蒸发塔制造过程质量分析等，证实了独山子石化乙二醇蒸发塔的裂纹属晶间型应力腐蚀裂纹。
By the analyses of corrosive medium and manufacturing process quality, the cracks of glycol evaporators in Dushanzi Petrochemical Company have been confirmed to be intergranular corrosion cracks.
通过GB／HDPE的拉伸实验和断口形貌分析，研究了颗粒体积分数、拉伸速率、界面强度对GB／HDPE复合材料力学性能的影响。
The effects of particle volume fraction, tensile rate and interface bonding strength on the properties of GB/HDPE composites were studied by tensile test and SEM observation.
通过对铝合金、结构钢等金属接触腐蚀表面的EDS成分分析和SEM微观形貌分析，探讨金属材料与玄武岩微纤维隔热材料接触腐蚀的原因。
Based on EDS and SEM analysis of metal corrosion surface, the course of contact corrosion between aluminum alloy, structural steel and basaltic microfiber heat-resistant materials were proposed.
用计算清洗失重速率、表面形貌分析、成膜分析等方法，通过高压釜挂片试验，研究了新型带负荷清洗剂在模拟炉水中对锅炉碳钢的清洗及钝化的效果。
The cleaning experiments of boiler steel in simulated boiler water in autoclave were performed by calculating weightlessness velocity, surface analyses, and analyses film-forming.
我们还分析了形貌对场发射性能的影响。
We also analyzed the effect of morphology on field emission properties.
分析了插销焊接接头的组织和插销试样的断口形貌。
Microstructure of the joints and fracture morphology of implant samples were analyzed.
原子力显微镜扫描对醛基化玻片表面形貌进行分析。
Scanning aldehyde group glass slide by atomic force microscopy study the surface shape.
采用着色腐蚀技术，金相显示了球墨铸铁缩松区中奥氏体枝晶组织形貌，分析了球铁缩松的形成机制。
The morphology of austenite dendrites in shrinkage porosity in nodular iron is displayed by the color etching technique and the formation mechanism of shrinkage porosity has been analyzed.
利用扫描电镜断口分析及金相分析技术，分析了材料拉伸试件断口形貌及金相组织，初步探讨了材料的静态拉伸塑性变形机理。
The metallurgical structure and fracture morphology of the tensile specimens were investigated with SEM and metallurgical analysis, and the static tensile plastic deformation mechanism was researched.
运用扫描电镜观察了这几种材料在泥沙磨损条件下的磨损表面形貌，分析了它们的磨损机理。
The wear surface morphologies were surveyed by scanning electron microscope (SEM) and wear mechanism was analyzed under the sand slurry wear condition.
球墨铸铁经过气体多元共渗后可在其表面形成氮化层，通过X射线衍射和扫描电镜对渗层的相结构与形貌进行分析。
The nitride layer was formed on the surface of ductile cast iron by gas multi-element penetration, and the phase structure and section appearance of nitride layer were analyzed by the XRD and SEM.
球墨铸铁经过气体多元共渗后可在其表面形成氮化层，通过X射线衍射和扫描电镜对渗层的相结构与形貌进行分析。
The nitride layer was formed on the surface of ductile cast iron by gas multi-element penetration, and the phase structure and section appearance of nitride layer were analyzed by the XRD and SEM.
应用推荐