探讨了剪力键的类型、试验承载力、以及其弹性和塑性设计方法。
The paper discusses shear key's species, test of bearing capacity and elastic theory and plastic theory.
结果表明：该合金的室温压缩变形过程表现为弹性和塑性变形，弹性应变很大，可达到2%。
We found: the samples experience elastic and plastic deformation processes before fracture, and the elastic strain is very large, it is about 2%.
第四部分，以个股为研究对象，随机抽取了20支股票，分别进行了股票价格弹性和塑性性质的研究。
Fourthly, making the single stock as our research object, the author selects 20 stock samples at random, then carries on the research respectively on elasticity and elasticity of the stock.
那一年，查尔斯·固特异偶然把橡胶和硫磺滴到热炉子上，引起橡胶象皮革一样焦化但依然保持良好的可塑性和弹性。
In that year, Charles Goodyear accidentally dropped rubber and sulfur on a hot stovetop, causing it to char like leather yet remain plastic and elastic.
同时给出了塑性激波后方弹性卸载区内的应力和质点速度分布规律。
Distributions of stress and particle velocity in the elastic unloading region behind the plastic shock wave are given as well.
钢桥的设计方法按其设计理论大体可分为弹性设计方法和塑性设计方法。
According to the basic design theory, the bridge design method can be divided into: the elastic design method and the plastic method.
土体总的变形由三部分组成：即弹性应变、与体积屈服机制相关的塑性应变和与剪切屈服机制相关的塑性应变。
The total deformation of soils consists of three parts: elastic strain, plastic strain related to volumetric yielding mechanism and plastic strain related to shear yielding mechanism.
借用物理学领域中有关材料的塑性和弹性的理论，用类比推理方法研究股票价格变化中体现的塑性和弹性。
This paper studies the plasticity and the elasticity of stock prices via analogical reasoning, with reference to material plasticity and elasticity in the field of physics.
讨论了母料的配比、用量和软化剂对热塑性弹性体SBS各种性能的影响。
The effects of combination ratio and dosage of masterbatch and softeners on the properties of SBS elastomer were investigated.
随养护时间的延长，水泥石低压应力下的弹性形变恢复能力和高压应力下的塑性形变能力均降低；
When curing time increasing, cement stone's elasticity deformation restorability in low stress and plasticity deformation capacity in high stress decreased.
当荷载被移走时，应变的弹性部分恢复，但塑性应变部分(滑移和徐变)却会永久呆留。
When the load is removed, the elastic portion of the strain is recovered, but the plastic part (slip and creep) remains as permanent set.
断口主要分为塑性屈服变形区和弹性变形区两部分。
Fracture surface consists of plastic yield deformation area and elastic deformation area.
其压缩过程可分为弹性段，塑性坍塌段和致密化段三个阶段。
The process can be divided into three stages: the linear elasticity, the plastic and densification.
在组合梁的计算理论中，作者分别详细地阐述了组合梁的弹性分析和塑性分析理论。
In terms of the calculating theories of the composite steel-concrete beam, the elastic analysis and the plastic analysis are expounded systematically.
对具有中心穿透斜裂纹在弹性断裂和完全塑性断裂两种破坏模式下的断裂强度进行了分析。
The fracture strength of rectangular plate with inclined crack is analyzed considering two failure modes of elastic fracture and fully plastic failure respectively.
在应变疲劳曲线上，弹性线和塑性线的交点随弹簧钢回火后硬度的升高而向低循环寿命移动；
The point of intersection of elastic line and plastic line moves toward the low cycle life with the hardness of the spring steel raised after tempering from the strain fatigue curve.
利用界面应力剪滞理论，分别建立弹性区和塑性区的界面力学基本方程。
By employing the shear lag theory, the basic equations of interfacial mechanics for the elastic zone and the plastic zone are established respectively.
目前，对钢筋混凝土连续梁板在竖向荷载作用下的计算，常用的有两种方法，即按弹性方法计算和按塑性方法计算。
At present, The calculation method of continuous board and beam under vertical loads has two methods: elastic method and plastic method.
采用递增应力流变学方法将弹性、塑性、断裂变形结合并与流体和化学耦合起来。
The elastic strain, plastic strain and fracturing are integrated and coupled with fluid and chemistry using an incremental stress rheological approach.
它耦合了三维刚塑性有限元法，弹性有限元法和计算辊系变形的影响函数方法。
Three-dimensional rigid-plastic finite elements, elastic finite elements and influential function method for the analysis of deformation of rolls system are combined.
分析弹性剪切力和塑性剪切力的形成及特征，剖析以往解析分析中存在的问题。
The formation and characters of elastic shear force and plastic shear force are analyzed.
弹性模量和塑性参数受溶解过程的影响。
The elastic modulus and the plastic properties are affected by the dissolution process.
提出了一个新的孔压公式；给出了非线性弹性模型和弹塑性模型的孔压系数的表达式。
It presents a new pore pressure formula and proposes an expression of pore pressure coefficient for non-linear elastoplastic models.
主要的类型有浇注型聚氨酯弹性体、混炼型聚氨酯弹性体和热塑性聚氨酯弹性体。
The main types are cast polyurethane elastomer, millable polyurethane elastomer and thermoplastic polyurethane elastomer.
黏合材料的黏弹性和黏塑性将会导致传感器输出的滞后和漂移误差。
The viscoelasticity and viscoplasticity of bonding material will result in hysteresis and drift errors to sensor output.
将具有一定应变硬地指数的二维裂纹体在单一载荷作用处的位移分成线弹性部分和塑性部分。
The load point displacement caused by single load for two dimentional cracked body with certain strain hardening exponent is divided into its linear-elastic and plastic components.
在宏观尺度上，弹性模量和塑性参数，包括对塑性孔隙塌陷机理和塑性剪切机理，被表达成水饱和度的函数。
On the macroscopic scale, the elastic modulus and the plastic parameters for both pore collapse and plastic shearing processes are expressed as functions of water saturation degree.
在宏观尺度上，弹性模量和塑性参数，包括对塑性孔隙塌陷机理和塑性剪切机理，被表达成水饱和度的函数。
On the macroscopic scale, the elastic modulus and the plastic parameters for both pore collapse and plastic shearing processes are expressed as functions of water saturation degree.
应用推荐