本文利用弹塑性有限元法分析了非轴对称拉延过程。
In this paper, an elastoplastic finite element method is used for the analysis of non-axisymmetric deep drawing processing.
采用弹塑性有限元法对斜坡的初始应力场特征进行模拟研究。
Then, the initial stress field of the slope is simulated by means of elastic-plastic finite element.
本文用弹塑性有限元法计算了中心裂纹板双向加载的J积分。
This paper the J-integral computation of biaxial loading in center cracked sheets with elastic-plastic finite element method is given.
蒙特卡洛随机搜索法与弹塑性有限元法结合，求解边坡稳定问题。
The Monte Carlo method combined with the elastoplastic finite element method (FEM) is proposed to analyze the slope stability problems.
采用三维热弹塑性有限元法对管板接头的焊接变形进行数值模拟。
Welding deformations of a pipe-plate joint with holes after multi-pass welding are simulated using the thermal-elastic-plastic finite element method.
采用三维弹塑性有限元法对四辊轧机轧制薄带钢的过程进行了模拟。
The thin strip rolling process of 4-high strip mill is simulated and analyzed by using 3-D elastic-plastic FEM with software MSC.
热弹塑性有限元法和固有应变法是焊接变形预测的两种主要数值方法。
Thermal-elastic-plastic and inherent strains FE methods are two means, which have been applied to the prediction of welding deformation.
本文用三维弹塑性有限元法计算了含圆孔对称复合材料层板的层间应力分布。
In this paper, the interlaminar stress distributions of symmetric composite laminates with a hole are predicted by the three-dimensional elastoplastic finite element method.
采用三维弹塑性有限元法对虎克式万向节热挤压成形过程进行了数值模拟分析。
This paper deals with the numerical simulation analysis of hot extrusion forming process of the Hooke's Joint using three-dimensional elastoplastic finite element method.
本文用弹塑性有限元法分析了中心受压钢管混凝土短柱的承载力与变形的关系。
In this paper the Elastoplastic FEM is used to analyze the relation between load capacity and deformation of the central loaded steel-tubed concrete column.
采用平面应力弹塑性有限元法研究了含有多部损伤的焊接接头裂纹尖端J积分的变化规律。
The J integral values in the vicinity of the crack tip in welded joints were numerically analyzed by using the plane stress elastic-plastic finite element method.
本文采用弹塑性有限元法和解析法，对分离机转鼓的主要零件进行了超速自增强的变形分析。
The deformation analysis of the main parts of the disc-separator bowl is performed for the overspeeding process using elastoplasticity FEM and analytical method.
采用弹塑性有限元法分析了柴家坡隧道在施工过程中注浆加固对滑动面和围岩稳定性的影响。
This paper analyses grouting reinforcement's influence on slide plane and surrounding rock stability during the construction in Caijiapo tunnel, using the elastoplastic finite element method.
采用弹塑性有限元法分析了柴家坡隧道在施工过程中注浆加固对滑动面和围岩稳定性的影响。
This paper analyses grouting reinforcements influence on slide plane and surrounding rock stability during the construction in Caijiapo tunnel, using the elastoplastic finite element method.
第二章介绍了有限单元法的基本原理，详细推导了弹塑性有限元法的基本公式和弹塑性矩阵。
Chapter 2: basic theories about finite element method are introduced, basic formulas about elastic-plastic finite element method and elastic-plastic matrix are put forward.
运用弹塑性有限元法，研究了胶粘剂弹性模量对含间隙的铝合金单搭接接头上应力分布的影响。
The effect of elastic modulus of adhesive on the str ess distribution in aluminium alloy single lap joint was investigated using elastic-plastic finite element method(FEM).
采用弹塑性有限元法和强度折减法，对九甸峡水电站厂房后岩体边坡进行稳定性计算分析和评价。
Based on the elastic-plastic finite element method and strength reduction method, the stability of the rock slope behind the powerhouse of Jiudianxia hydroelectric station was studied and evaluated.
为消除铝合金预拉伸板中的残余应力，采用弹塑性有限元法对振动时效消除残余应力进行数值模拟。
To eliminate the residual stress of aluminum alloy pre-stretching board, an elastic-plastic finite element model was developed to simulate the vibratory stress relief (VSR) process.
用弹塑性有限元法分析超速预过载处理后叶轮的残余位移、应变及应力场 ，给出相应的求解结果。
We used periodic symmetry constraint on FEA Model. Elastic plastic finite element principle used in analysis process.
采用二维轴对称弹塑性有限元法对比分析了不同外模模角和游动芯头锥角的配合对拉拔铜管的影响。
This paper focuses on the comparison of the matching of dies and floating plugs with different Angle with the aid of 2d axisymmetric elastic-plastic FEM and the influence of drawing copper tubes.
以T形焊接接头为算例，结合热弹塑性有限元法和映射应变分量法，研究了角焊缝角变形的产生机制。
The conception of deformation angle of helix pre-former is introduced and process parameters are analyzed with math regression method.
运用弹塑性有限元法结合实验研究了连续和间隙连接的单搭接接头应力分布规律，并考虑了胶瘤的影响。
The stress distribution of continuous and recessed bonding single-lap joints is discussed with use of elastoplastic finite element method (FEM) and experiment, considering the effect of fillet.
并基于塑性理论，编制了“墙梁结构弹塑性有限元法计算程序”，对一些算例进行了验算，得到较好的结果。
A finite element program of wall beam structure under elastoplasticity condition is compiled based on the plastic theory and used to test some practical samples.
并基于塑性理论，编制了“墙梁结构弹塑性有限元法计算程序”，对一些算例进行了验算，得到较好的结果。
A finite element program of wall beam structure under elastoplasticity condition is compiled based on the plastic theory and used to test some practical samples. The result is perfect.
采用弹塑性有限元法，结合非线性屈曲理论，分析了受初始几何缺陷影响的管线钢管在内压作用下的非线性屈曲。
Secondly, with the first mode of eigenvalue analysis on SSRS as the initial disfigurement, nonlinear buckling loads are obtained by nonlinear buckling analysis.
针对钢板冷却发生翘曲变形的问题，利用热弹塑性有限元法对中厚板冷却过程的温度场及应力应变场进行数值模拟。
The temperature and stress-strain field of steel plate runout table cooling are simulated using thermo-elastoplastic finite element method.
给出了有限变形弹塑性有限元列式，基于A NSYS软件平台，介绍了弹塑性有限元法在金属塑性加工领域中的应用。
The finite deformation elastic-plastic finite element formula are given. Based on the ANSYS software, the application of elastic-plastic FEM on metal plastic process field is outlined.
模拟结果证实了应用显式动力学弹塑性有限元法模拟双金属复合板轧制的可行性，且计算所得轧制力与实验结果吻合较好。
The specific rolling force distribution was obtained by simulation and the calculated results of rolling force are in good agreement with the measured ones.
应用热弹塑性有限元法对液力变矩器点固焊过程夹持力和焊接变形进行全面分析，定量得出了焊接预留间隙，为夹具设计提供了依据。
According to the analysis results, pre-welding gap was gained quantitatively, which can be regarded as warrants and references for the design of welding clamps.
应用热弹塑性有限元法对液力变矩器点固焊过程夹持力和焊接变形进行全面分析，定量得出了焊接预留间隙，为夹具设计提供了依据。
According to the analysis results, pre-welding gap was gained quantitatively, which can be regarded as warrants and references for the design of welding clamps.
应用推荐