该clk引脚输出将被设置为晶振频率。
The output of the CLK pin will be set to the crystal frequency.
在SCART的模式，该引脚输出的绿色信号。
在正常的操作模式比其他的SCART，该引脚输出视频信号的色度。
In normal operating modes other than SCART, this pin outputs the chroma video signal.
其中数据总线sda是一个双向引脚，用于输入或输出数据。
Which the data bus SDA is a bidirectional pin used for input or output data.
该引脚是误差放大器的输出，并提供环路补偿。
Compensation: This pin is the Error Amplifier output and is made available for loop compensation.
数据切换的设备和输出通过写入和读取的引脚使用。
Data is toggled in and out of the devices through the use of the Write and Read pins.
外部逻辑控制引脚用来选择输出电流组合，并能够使芯片进入关断模式；
Shutdown mode and current output levels are selected via two control logic inputs.
每个引脚需要一个输出使能信号。
算法以引脚间输入与输出信号之间的延时——判别时间窗作为识别的重要参数，设计了详细的信号识别算法。
The algorithm principle is based on the input-output signal "s time delay distinction time window as the key parameter, and the detailed signal identification algorithm."
第一解调器接收数字信号，并首次通过数字输出信号引脚的MPEG信号。
The first demodulator receives the first digital signal and outputs an MPEG signal via the digital signal pins.
无论是能量收集降压变换器或电池降压-升压转换器可以提供能量到设备的输出引脚。
Either the energy-harvesting buck converter or the battery buck-boost converter can deliver energy to the device's output pin.
出于这个原因，电路使用mclr引脚作为输出。
For that reason, this circuit USES the MCLR pin as an output.
电路使用带引脚和低有效输出的复位管理芯片。
The circuit employs a reset-supervisory chip with the pin and active-low output,.
使用MAX038波形发生芯片产生波形，通过修改MAX038相应引脚的参数方便地实现输出波形的频率和占空比及偏置电压参数的调节。
The waveform is generated by MAX038. It is very convenient to adjust the frequency, duty cycle and offset voltage of the waveform by changing parameters of the corresponding pins of the chip.
因此，本设计需要一个额外的输出引脚。
当门开关关闭(车门打开)的引脚电压慢慢上升8以上的三角形产生短期占空比输出波形的负峰和一个暗淡的灯光。
When the door switch is closed (car door open) the voltage on pin 8 slowly rises above the negative peaks of the triangle wave producing a short duty cycle output and a dim light.
根据试验和理论分析，这种现象是由多路模拟开关输出引脚上的分布电容引起的。
According to tests and theoretical analysis, it is found that the distributing capacitors cause the inter-channel influence phenomenon.
根据芯片的引脚功能、性能参数，设计了系统的硬件原理图，详细说明了各芯片的输入输出信号。
Following the function of each pin, performance parameters of chosen chips, this paper designed hardware diagram of system, and detailed the input and output signals of chips.
网络变压器模块市场需求量非常大，提高生产效率的主要瓶颈是，变压器绕组的漆包线焊接到输入输出引脚上。
Network transformer module market demand is very large, and increase productivity of the main bottleneck is that the transformer windings of the wire soldered to the input and output pins.
本设计使用一个模拟输入和三个输出引脚。因此，本设计需要一个额外的输出引脚。
This design uses one pin for analog input and the other three as outputs.
同样的外围设备、输出引脚以及单一开发工具套件装置，既适合8位也适合32位微处理器，产生真正管教兼容的32位设备来替代8位产品。
Identical peripherals and pin-outs and a single tool set suitable for both 8 - and 32-bit devices can produce a 32-bit device that's a true pin-compatible, drop-in replacement for an 8-bit product.
同样的外围设备、输出引脚以及单一开发工具套件装置，既适合8位也适合32位微处理器，产生真正管教兼容的32位设备来替代8位产品。
Identical peripherals and pin-outs and a single tool set suitable for both 8 - and 32-bit devices can produce a 32-bit device that's a true pin-compatible, drop-in replacement for an 8-bit product.
应用推荐