具有卓越的润滑性能，减少了大功率发动机的异常磨损。
The lubricated performance with brilliance, has reduced the unusual wearing and tearing of the high-power engine.
当负载电流过大时还有可能产生电火花而引起异常磨损。
The brush will produce abnormal wear with the appearing of the electric spark when overload current passes.
论文把图像处理与识别技术直接应用到气缸套表面异常磨损检测中。
The paper applies the technology of image processing and recognition to the detection of abnormal abrasion on the surface of cylinder liner.
重新调整后，解决了该车轮胎异常磨损问题，并确认该车的设计参数是合理的。
After the readjustment, the problem of the abnormal wear of tyre was solved, and the passenger car's design parameter is firmly reasonable.
这有助于防止关节炎也许成为一个问题，假如他的骨头上，由于彼此的错位异常磨损。
This can help prevent arthritis that might become a problem if his bones are wearing on one another abnormally due to the dislocation.
现场实测结果表明，利用柴油机表面振动信号来诊断柴油机主轴瓦异常磨损故障是可行的。
The real detecting result shows that it is feasible to use the engine surface vibration signal to diagnose main bearing shell abnormal wear trouble.
汽车转向梯形机构的设计在汽车设计中占据重要的地位，合理的设计可以减小车轮在转向过程当中的滑动，使轮胎的异常磨损控制在允许的范围内。
The design of Ackerman geometry plays a very important role on vehicle design, reasonable design could reduce the slipping in turning, make the abnormal wear in a permissive range.
机构铰接副处过大间隙将引起异常的振动与噪声，加速了疲劳与磨损，严重地影响了机器的动态性能。
Excessive clearance of mechanism joint pair will cause abnormal vibration and noise, accelerate fatigue and wear and seriously affect the dynamic performance of machine.
高温、高压、高压差的蒸汽调节阀中的流动不稳定导致异常的振动，造成阀门的磨损及阀杆破坏以及流动中的压损。
The unsteady flow in the high pressure steam valve cause unusual vibration, the valve pole to be destroyed, the pressure while flowing to be lost, etc.
由于高地应力作用与岩爆的影响，刀具的异常破坏过多，刀具的磨损预测不是很理想。
Due to the influence of the high in-situ stress and rock bursts, the abnormal cutter failure is too much. Thus, the predicted results for cutter life are not good.
某化工厂反应釜搅拌轴运行中经常出现异常现象，轴头部位磨损严重。
Abnormal phenomenon of stirring shaft in a chemical plant often occurs in operation. The shaft head is seriouslv worn.
分析了日本帝人公司生产的P75 -2 4A螺杆挤压机套筒镶套磨损的原因是环结阻料或异常卡车 ，提出减少磨损的几条措施。
The reasons for wear and tear of the inlay sleeve of sleeve of P75\|24A screw extruder made in Japan were analyzed, and some measures to reduce wear and tear of the inlay sleeve were proposed.
分析了日本帝人公司生产的P75 -2 4A螺杆挤压机套筒镶套磨损的原因是环结阻料或异常卡车 ，提出减少磨损的几条措施。
The reasons for wear and tear of the inlay sleeve of sleeve of P75\|24A screw extruder made in Japan were analyzed, and some measures to reduce wear and tear of the inlay sleeve were proposed.
应用推荐