内容包括时基电路、预置延时电路、输入接口、总清及加电复位等。
It includes the time-base circuit, time set and delay circuit, input interface, clear and reset circuit etc.
对采用CMOS缓冲器组成电容充放电式长时间延时电路进行了研究。
How to use the CMOS buffer to make up the capacitance charge-discharge type long time delay circuits is studied.
它由传感器、信号放大电路、比较输出电路、延时电路和可控硅组成。
The utility model is composed of a sensor, a signal amplification circuit, a comparison output circuit, a delay circuit and controllable silicon.
其中开关电路由射极耦合触发电器、积分延时电路、单稳态电路三单元构成。
The switch circuit is composed of an emitter-coupled trigger circuit, an integral delay circuit and a monostable circuit.
通过对高压器件的防击穿保护，并增加适当的延时电路，大幅度提高了驱动电路的工作稳定性。
The circuit 's working stability is improved greatly through anti-breakdown protection and adding appropriate time-delay circuit.
采用模拟回波和精密延时电路检测照射能力、用CCD采集激光光斑测试激光束散角，实现了整机性能的数字化检测。
Using simulation echo wave and accurate time delay circuit to measure ranging ability, using CCD to grasp laser facular to measure divergence of laser pulse, the digitized methods are realized.
在电路设计过程中，对后级接口电路进行了最优化设计，采用VHDL描述的方式实现了低压数字延时电路模块的设计。
In this paper, the optimization method was used to design the interface circuit, and use VHDL description to design low voltage digital delay timer.
本文对并联延时控制系统和决策延时控制系统的延时精度进行分析，给出延时控制系统中各延时电路延时值的选取原则。
By analysing the delay precision of parallel connection delay control system and decision-making delay control system, the choosing principle of the delay time for every delay circuit is given.
因此研究互连延时成为当今进行电路设计和工艺的重点。
Thus, the study of interconnection delay becomes more important for current circuit design and technology.
检查电器箱接线及紧固情况，调整延时继电器及过载保护器，接通电路，试验电机转向，选择合适规格的保险丝。
Check the electrical box wiring and tighten the situation, adjust delay relays and overload protector, connect circuits, test motor steering, select the appropriate specifications of the fuse.
使用单稳态触发电路作“延时”或“定时”用，由于受到元件和器件的影响，其精度不会太高。
The accuracy of delay or timing is not sensitive with monostable trigger circuit since electrical elements have influence on it.
本文介绍床边摄影曝光延时指示灯的制作电路设计及工作原理。
This paper introduces the circuit design and working principle of bedside photography exposure delayed indicator.
在交流电路中常采用空气阻尼型时间继电器，它是利用空气通过小孔节流的原理来获得延时动作的。
Often in ac circuit by air damping model time relay, it is to use the principle of air through orifices throttling to obtain delay action.
本文提出一种新型的用于IGBT驱动、保护及信号分配延时的电路方案。
A new circuit scheme of drive, protect, signal distribution and delay for IGBT is proposed.
目前最常用的为大规模集成电路型成的时间继电器，它是利用阻容原理来实现延时动作。
The most commonly used for large scale integrated circuit of the time relay into, it is to use resistance to achieve delay action let principle.
给出了看门狗、掉电后供电延时、电源故障实时监控和自动复位等功能的实现电路及相关程序。
The implementing circuits of watchdog, delay on power outage, power failure monitoring and automatic reset and related program are given.
文中对开、关机的过渡过程进行了分析，还介绍了有关欠压保护、硬件开机延时及其它保护电路的设计。
The paper analyses the transition process from start to shut of the system, and deals with the under-voltage protection, hardware start delay and the design of some other protection circuits.
本文研究了双极型电路传输延时的约束机理。
A study of limitation mechanisms to propagation delay of bipolar circuits has been carried out.
采用电子消弧电路取代传统的消弧继电器，提高了消弧延时的精确性和可靠性。
It also indicates that the accuracy and reliability of time retardation for arc extinction can be increased by replacing traditional extinction relay with electron extinction circuit.
介绍了一种采用CMOS数字电路、数字拨盘开关整定、无辅助电源的断电延时继电器的组成及工作原理。
Introduction was made to the composition and working principle of a power-off time delay relay which adopts CMOS digital circuit, digital dial disc for switch setting and without auxiliary power.
电路设计具有断电延时功能，确保制冷压缩机电机启动时不受损害。
The circuit is designed to have power-off-delay function to ensure no any damage happens when the motor for refrigeration compressor is started.
提出了有源钳位准谐振变换器的一种新的驱动方式，它无需经过数字电路延时，只需一个电阻和二极管构成的小网络。
This paper proposes a new gate drive method for active clamped quasi resonant converters. Instead of a digital delay circuit, only a resistor and a diode are added to produce correct drive waveforms.
按钮式控制数字电位器x 9511由延时去抖动电路、单稳电路、触发器组成。
Button control digital potentiometer X9511 is consists of time delay circuit removed dithering, mono - stability circuit, preventative dithering trigger.
研究了交换控制电路中基于输入缓冲的交换结构，提出了一种请求移位的方法处理输入缓冲和中央仲裁器之间的仲裁延时；
This paper describes the implementation of buffer manager that is used in switch circuit, provides a request shift method to handle the latency between input buffer and central arbitration.
过程变化的知识对于最优化电路延时，减少时钟倾斜和降低串扰噪声很重要。
Knowledge of process variation is important to optimize critical path delay, minimize clock skew, and reduce crosstalk noise.
实现了一种既能对随机性脉冲进行累计性分段延时，亦可进行单一时间延时的电路，实用性较好。
This paper introduces a very practical circuit which can perform both the random pulse accumulative segmented time-delay and single time-delay.
早期在交流电路中常采用空气阻尼型时间继电器，它是利用空气通过小孔节流的原理来获得延时动作的。
Early in the circuit often USES air damping model time relay, it is to use the principle of air through orifices throttling to obtain delay action.
在标准测试电路上的测试结果表明引进延时再优化能给异步电路的平均延时带来6～25%的改进。
The experimental results on a set of benchmark circuits show that this algorithm can improve the average delay of asynchronous circuits by 6~25%.
提出了用来评估深亚微米vlsi电路中rlc互连延时的一种新的解析延时模型。
This paper presented an innovative analytical delay model for RLC interconnects utilized in the estimation of interconnect delay for deep submicrometer VLSI circuits.
提出了用来评估深亚微米vlsi电路中rlc互连延时的一种新的解析延时模型。
This paper presented an innovative analytical delay model for RLC interconnects utilized in the estimation of interconnect delay for deep submicrometer VLSI circuits.
应用推荐