这种大变形如果仅是应力重分布引起的体积膨胀则称为岩石扩容。
This large deformation is called for rock dilatancy if volume dilation only occurs owing to stress redistribution.
而淬火引入非均匀的结构应力且梯度较小，主要发生应力重分布。
However, stress re-distribution would occur in the non-uniform structural stress introduced by quenching with a low stress gradient.
基于此模型，分析了受拉伸的层内混杂复合材料中某些纤维断裂后的应力重分布。
Based on the model, the stress redistributions due to the failure of some fibers in an intraply hybrid composite under tension are analyzed.
然后采用该方法分析徐变对结合梁中的应力重分布的影响，并对徐变的影响进行参数分析。
With this method, the influence of creep on stress redistribution in composite beams has been analyzed, and rheologic parameters was studied .
路基的热状况、水分状况与变化规律及由此引起的应力重分布是引起道路冻害的主要因素。
Both the condition of the heat, the moisture of the subgrade, their changing law and the stress distributing are the key factors to cause the frost damages.
软土路基中三维固结效应以及路堤的应力重分布产生的水平推力，引起的侧向变形是不容忽视的。
For the three-dimensional consolidation effect impersonal existence of roadbed and the horizontal thrust from stresses re-distribution of embankment, soil lateral deformation should not be neglected.
本文分析指出，地面沉降现象可用地下抽水作用引起土层内应力重分布和由此导致的变形作合理的解释。
Analysis shows that the phenomena of land subsidence can be well interpreted by stress redistribution and its consequent deformation occurred in the soil layer as a result of subterranean pumping.
建立了负重轮的三种三维有限元力学模型，在考虑三重非线性的情况下，用ANSYS有限元分析软件计算了负重轮的应力应变分布。
Under the condition of three kinds of nonlinearity the stress and strain distribution of the road wheel is calculated with finite element analysis software ANSYS.
基于两榀接近足尺的后张有粘结预应力混凝土框架的试验，对多跨预应力框架的内力重分布进行了研究，重点考虑了框架的连续性和轴压比的影响。
Based on tests of two full-scale double-span prestressed frames, internal force redistribution of frame was studied and continuity of structures and axial compression ratio of column were analyzed.
掌握锚固区域在斜拉索作用下的应力大小及分布是十分重要的。
It is very important to know the stress distribution of anchorage zones under cable forces.
在各种承载部位，在不改变其应力分布的前提下开设减重孔，利用去除材料来达到减重的目的。
Without changing stress distribution, holes are dug in bearing the weight of positions by wiped off material in order to decrease weight.
预应力框架中塑性铰形成的位置不同，弯矩重分布的方向和能力也不相同。
The position of plastic hinge will effect the direction and ability of moment redistribution.
研究并分析了体外预应力混凝土连续梁弯矩重分布的规律及其影响因素。
The redistribution of moment of model beams and its effect factors are studied and analyzed.
在这过程中，发生应力释放、传递和重分布。
Be living in this process, happening stress sets free and transfer and subdivision fibaric.
梁柱节点是结构设计的重难点之一，其连接处应力集中、应力分布复杂，设计和施工处理都比较复杂。
The joint of a frame is the keystone in structural design, the stress with a complicated distribution were concentrated in the connection, that makes the node difficult to be designed and constructed.
在这过程中，发生应力释放、传递和重分布。
In this process, stress release, transfer and redistribution appear.
关于预应力结构的内力重分布研究很多是关于连续梁结构的，对预应力框架的研究相对较少。
Most of the research on moment redistribution is based on continuous beam structures, a little on prestressed concrete frames.
讨论了部分预应力比PPR对连续梁内力重分布的影响；
The effect of PPR on the redistribution of bending moment was discussed.
本文叙述了悬臂拼装预应力混凝土连续梁的预加力引起的弯矩重分布。
In this paper the moment redistribution due to prestressing in precast segment continuous prestressed concrete beam erected by cantilever method is described.
因此，对微电子封装器件的温度分布以及热应力进行研究就显得十分重要，具有重要的理论和实际意义。
Therefore, research on temperature distribution and thermal stress of micro-electronic package is very important, which has both theoretical and practical significance.
关于预应力结构的内力重分布研究很多是关于连续梁结构的，对预应力框架的研究相对较少。
The moment modulation of prestressed concrete frame has some differences compared with that of continuous beam.
通过SAP2000和ANSYS程序的分析，本文主要结论有：1。预应力的使用引起结构构件的内力重分布。
By using SAP2000 and ANSYS program, the conclusion we can get: 1. The use of pre-stressed structural members caused by redistribution of internal forces.
通过SAP2000和ANSYS程序的分析，本文主要结论有：1。预应力的使用引起结构构件的内力重分布。
By using SAP2000 and ANSYS program, the conclusion we can get: 1. The use of pre-stressed structural members caused by redistribution of internal forces.
应用推荐