髓核内的应力和位移变化相对较小。
The intra- stress and displacement of nucleus wascomparatively lesser.
总的看来应力和位移的分布规律大体上一致。
The distribution laws of stress and displacement are generally consistent.
应力和位移的计算结果和测量结果基本一致。
The calculated results of stress and displacement are approximately consistent with the measured results.
自然边界积分方程分析可直接获得边界应力和位移导数。
The natural BIE can be employed directly to obtain boundary stresses and displacement derivatives.
成层碾压混凝土结构的内部应力和位移对其设计十分重要。
It is very important for designers to understand the inner stresses and displacements of layered roller compacted concrete structure.
采用有限单元法对巷道注浆支护时的围岩应力和位移进行了计算分析。
The finite element method is used to calculate and analyze the stress and the displacement of host rock when the openings is under the jet grouting support.
给出了闸墩各部位在不同时间、水温和水位情况下的应力和位移分布。
Under the situations of different time and water's locations, the distributions of the stress and displacement of various places are presented.
应用粘弹塑性力学和岩石力学理论，详细讨论了粘弹性岩石井眼的应力和位移。
The stress and displacement of wellbore with viscoelastic rock are discussed in detail by using viscoelastic-plasticity mechanics and rock mechanics theory.
通过优化设计，在应力和位移有所下降的基础上，使得动力头支架重量减轻6%。
After optimized, the weight of the frame reduced 6%, and the stress and displacement also descended.
通过分析不同的应力和位移边界条件得到了三种不同双层管结构中扭转模态的频散方程。
Dispersion equations of torsional modes in three different two-layer pipes are obtained by means of analyzing different stress and displacement boundary conditions of these structures.
再串行组集和求解界面方程得界面位移，最后返回各个子区，并行求解内点应力和位移。
By serially assembling and solving global equation to get interface displacements and backing to every sub-region, the inter-nodal displacements and element stresses can be solved.
采用角度细分逐次迭代的有限元分析方法解决了特殊圆弧三角形部件应力和位移分布问题。
In this paper, the distribution of stress and displacement of the special arc triangle components is solved by using the Angle division iteration method of finite element analysis.
采用双材料基本解建立边界元法基本方程，计算双材料界面裂纹尖端附近的应力和位移场。
The stress intensity factors of bimaterial interface crack are analyzed using the boundary element method with bimaterial fundamental solutions.
证明在静态情况下，几何对称试件和几何非对称试件的轴线两侧均具有对称的应力和位移分布状态；
The results show that the static stress and displacement states are symmetrical on opposite sides of the axis whether the sample is symmetry in geometry or not.
针对均布载荷作用下正交各向异性梁在两端固支条件下的平面应力问题，求解了应力和位移的解析解。
For the plane stress problem of fixed end orthotropic beams subjected to uniform load, the analytical solutions of stress and displacement were resolved.
在分析受不均匀荷载作用的立井井壁应力和位移的基础上，提出了确定立井井壁椭圆荷载的反分析方法。
On the basis of the analysis of shaft lining stress state and displacement state, proposed the back analytical method for determination of the elliptic load acting on shaft lining.
揭示了锚杆对岩体提供应力和位移约束机理。从而为深部不稳定巷道的支护设计与稳定性分析提供了依据。
The results show that bolts can offer both stress constraint and displacement constraint to rock mass, and provide a basis for support design and stability...
最后，通过渗流场与应力场的相互迭代，对比迭代前后应力和位移的变化，进行了渗流场和应力场的耦合分析。
In the end, with iteration of seepage field and stress field, change of stress and displacement before and after iteration are compared and coupling of seepage field and stress field is analyzed.
由于状态方程中的诸力学量正好是叠层壳的层间必须协调的应力和位移诸量，因此该文方法便于求解叠层结构。
Because all mechanical quantities appearing in the state equation are just the compatible quantities at the interfaces, the presented method is extremely convenient for solving the laminates.
分析了采高和支架对顶煤应力和位移分布的影响，为顶煤破碎机理的分析和顶煤移动和运动规律的研究提供了依据。
Mining high and support have influence on stress and displacement distribute of top coal, which offer the basic law of mechanical for top coal broken analysis and movement.
对这些有缝结构进行计算分析时，接缝及裂缝状态的变化会使得接触界面的范围和界面上的应力和位移不断发生变化。
When analyzing structures with joints or cracks, state changing of these interfaces will affect stress and displacement of contact surface.
分析方法是半解析法，没有应力和位移模式的假设，不限制壳的厚度，不要求两壳间的连接弹簧或其它支撑弹簧均匀分布；
A semi-analytical method with no assumption of stress and displacement is developed, in which the thickness of shell is not restricted and the uniform distribution of springs is not needed.
基于对称和反对称问题中应力和位移分量满足的必要条件，分析了主方向上应力状态的对称和反对称特点，并用算例加以验证。
Based on the necessary conditions satisfied by stress and displacement, we analyzed symmetry and antisymmetry under the principal stress state using a computational example.
通过静力有限元计算，得到了钢水罐回转台在自重和钢包满包载荷作用下的应力和位移分布，进而对结构的强度和刚度进行了分析。
The distributions of stress and displacement of the integrity of the ladle turret under the actions of self-weight and the static loads are firstly obtained based on the static FE analysis.
推导了考虑几何非线性项的结构形状优化位移灵敏度和应力灵敏度计算列式。
This thesis deduces computational formulations of displacement sensitivity and stress sensitivity in structural shape optimization considering geometric nonlinear element.
分别采用六种载荷边界条件和三种位移边界条件对曲轴应力和变形进行了有限元分析；
The stress and deformation of crankshaft are calculated by finite element method with six load boundary conditions and three displacement boundary conditions.
文末给出了算例，分析了隧洞的半封闭特性对应力、位移和孔隙水压力的影响。
Examples are presented at the end of this paper to analyze the influence of the partial sealing property of tunnel on stress, displacement and pore pressure.
同时研究了数值分析中温度荷载作用下应力边界条件和位移边界条件对温度应力的影响。
To investigate the influence of mechanical boundary conditions on the thermal stress, a comparison of the results between displacement boundary and stress boundary is made.
物料离心液压引起的最大应力和最大径向位移都随着转鼓壁厚的减小而增大。
With the decrease of thickness of drum wall, the maximum of stress and radial displacement created by materiel pressure increase.
物料离心液压引起的最大应力和最大径向位移都随着转鼓壁厚的减小而增大。
With the decrease of thickness of drum wall, the maximum of stress and radial displacement created by materiel pressure increase.
应用推荐