髓核内的应力和位移变化相对较小。
The intra- stress and displacement of nucleus wascomparatively lesser.
今天的儿童正在大量的应力和应变。
应力，应力和应变的转换，虎克弹性。
Stress, Transformations of Stress and Strain, and Hookean Elasticity.
薄膜具有较低的残余应力和较好的热稳定性。
The AlN films have low residual stress and well thermal stability.
隧道围岩应力和变形分析是隧道设计的重要内容。
The stress and deformation analysis for surrounding rock of tunnels is an important task in tunnels design.
由循环应力和化学腐蚀同时作用导致的一类失效。
Corrosion fatigue. A type of failure that results from the simultaneous action of a cyclic stress and chemical attack.
应力和变形均在设计允许范围内，工作性态正常。
The stress and deformation are in design range, and it works normally.
这有助于计算容器的一次薄膜应力和二次弯曲应力。
This is useful in evaluating the primary membrane stress and the secondary bending stress in vessels.
测量的关键参数是型钢与混凝土之间的粘结应力和滑移。
Key parameters measured are bond stress and slip between structural steel and concrete.
还非常适合在受振动、机械应力和强烈腐蚀的环境中应用。
They are also well-suited for applications experiencing vibration, mechanical stress and strong erosive forces.
成层碾压混凝土结构的内部应力和位移对其设计十分重要。
It is very important for designers to understand the inner stresses and displacements of layered roller compacted concrete structure.
应用罗代参数对压延工艺中的凸缘部分进行应力和应变分析。
Lode parameters are used to analyze the stress and the strain of the flange in calendering.
从她问我问题的角度看，她会有较强的适应力和向前的动力。
From the perspectives that she asked my questions, she will have great adaptation and motivations towards.
如果一个词有三个或更多的音节，有一个主应力和二次应力。
If a word has three or more syllables, there is a primary stress and a secondary stress.
从唯象观点分析了循环变形期间相变应力和弹性模量的变化。
The change of transformation stress and the modulus of elasticity during cyclic deformation was analyzed from the continuum mechanical point of view.
推荐的基础上的附加应力和系统运行测试运动可以成为里程碑。
Promoted builds on which additional stress and system test campaigns are run can become milestones.
同时给出了塑性激波后方弹性卸载区内的应力和质点速度分布规律。
Distributions of stress and particle velocity in the elastic unloading region behind the plastic shock wave are given as well.
用于涡轮机叶片在动态状态下对其振动频率、动应力和温度进行遥测。
It is for telemetering the vibration frequency, dynamic stress and temperature of turbine blades under dynamic state.
最佳答案之间的关系应力和应变在一个特定的物质决心通过拉伸试验。
The relationship between stress and strain in a particular material is determined by means of a tensile test.
作者就赫兹应力和旋转弯曲应力联合作用下的接触疲劳进行实验研究。
Experiments of contact fatigue under the action of combined stresses-Hertsian stress and rotating bending stress were carried out.
采用有限单元法对巷道注浆支护时的围岩应力和位移进行了计算分析。
The finite element method is used to calculate and analyze the stress and the displacement of host rock when the openings is under the jet grouting support.
给出了闸墩各部位在不同时间、水温和水位情况下的应力和位移分布。
Under the situations of different time and water's locations, the distributions of the stress and displacement of various places are presented.
通过膜应力和弯曲应力分布的特点，验证了板的屈曲过程的非线性特性。
The characteristic distributed for the membrane stress and crooked stress, has proved the bucking course of the panel is non-linear.
直接对曲梁剪应力的积分方程求解，导出了曲梁剪应力和径向应力的计算公式。
The shearing-stress formula in curved beams can be derived by solving directly an integral equation, and the formula for radial stresses is also presented in this paper.
对受弯构件受拉翼缘外侧粘贴FRP后的界面剪应力和界面剥离应力进行了分析。
The interfacial shear stress and peel stress between the FRP and the surface of tension flange were analyzed when the FRP was bonded to the tension flange of the bending members.
脱硫吸收塔结构及荷载形式复杂，常规设计计算方法不能给出其应力和变形分布情况。
The structure and load form of the absorbing tower is complex and regular design and calculation method cannot give its distribution condition of the stress and deformation.
分别采用六种载荷边界条件和三种位移边界条件对曲轴应力和变形进行了有限元分析；
The stress and deformation of crankshaft are calculated by finite element method with six load boundary conditions and three displacement boundary conditions.
应力敏感性是指骨架应力和孔隙流体压力共同作用产生的压差对微观孔隙结构的影响。
Stress sensitivity means the influence of pressure difference produced by joint working of the matrix stress and the porous fluid pressure on the porous microstructure.
应力敏感性是指骨架应力和孔隙流体压力共同作用产生的压差对微观孔隙结构的影响。
Stress sensitivity means the influence of pressure difference produced by joint working of the matrix stress and the porous fluid pressure on the porous microstructure.
应用推荐