设备设计师能通过审慎地选择输入输出级电路的拓扑和共模阻抗来最小化失配或“非平衡”的效应。
Equipment designers can minimize the effects of these mismatches or "unbalances" through judicious choices of input and output stage circuit topologies and common-mode impedances.
与单检测器相比，平衡式检测具备更高的灵敏度，因为这种检测方式拒绝共模噪声，而且光能利用率更高。
Balanced detection provides better sensitivity over a single detector because it rejects common mode noise and is more efficient in light usage.
在平衡电路中，节点处奇次谐波流过差分路径。偶次谐波流过共模路径。
In any balanced circuit, odd harmonics circulate in a differential path, while even harmonics flow in a common-mode path.
指出，只有当附加磁场与等离子体接近不稳定边界的模相耦合时，才可能引起平衡位形很大的变化。
It is pointed out that a large variation in the equilibrium configuration may take place only when the small magnetic perturbations couple with the plasma modes which are almost neutally stable.
基于气田的物质平衡方程序，在本文中提供了确定定容封闭气田地质储量的诺模图。
A nomograph for determining gas in place (GIP) in a closed gas field is presented in this paper based on the material balance equation.
最后，利用非奇异终端滑模控制技术，得到了一种使闭环系统有限时间收敛到平衡点的反馈镇定控制器。
Finally, using nonsingular terminal sliding mode technology, a feedback stabilizing controller which can make the closed loop system converge to equilibrium in finite time is given.
本文推导了平衡化补偿的实用公式，并利用动模实验进行了验证。
A practical formula for balancing compensation is presented. The formula has been verified by physical-simulation experiments.
由于零模参数受大地电阻率等因素影响，能量平衡保护采用了较为稳定的空间模量计算能量。
Owing to the influences of such factors as the earth resistivity on the zero module parameter, the stable space module is adopted to calculate energy for energy balance protection.
液压缸压力转换熔融塑料在模腔的填充平衡需要液压缸压力驱动螺杆前进来保证。
Hydraulic pressure switchover the packing of the melt in the mould cavity has to be balanced by the hydraulic pressure driving the screw forward.
由于交叉相位调制与偏振模色散相互作用的平衡，导致了一些诸如孤子自捕获、呼吸子对的现象出现。
Due to the balance of XPM and PMD. Some phenomena appear such as soliton self-trapping and a breather pair.
介绍了节流阀在非平衡型腔注射模中的应用及模具工作过程，并分析了节流阀的设计要点。
The application and working process of throttle valve in injection mold of unbalanced cavities were introduced, and the key points of designing throttle valve was analysed.
采用机械式气囊平衡装置，平衡滑块和上模重量，使机床运行更平衡。
Adopt mechanical air-bag balance device to balance weight of he slide and the upper die so than machine operates more smoothly.
下模自动调节平衡，下模可根据不同产品，随时更换适合不同产品。
Automatically adjust the balance of the lower mold, the lower mold according to different products, change at any time for different products.
双平行、平移模机构，中心锁模，平衡受力，移动迅速，到位平缓。
Two parallel, the mould organization of translation, the centre locks the mould, balance the strength of receiving, move rapidly, put it in place gentlely.
特点：1、高效率真空系统2、缓冲平衡器装置，同一模站内可自动补偿模厚2mm以内，节省模具调校时间。
Features:1. Efficient vacuuming system. 2. Hydraulic cushion equipment: Moulds thickness can be compensated for max. 2mm on one mould station to save mould correcting time. 3.
特点：1、高效率真空系统2、缓冲平衡器装置，同一模站内可自动补偿模厚2mm以内，节省模具调校时间。
Features:1. Efficient vacuuming system. 2. Hydraulic cushion equipment: Moulds thickness can be compensated for max. 2mm on one mould station to save mould correcting time. 3.
应用推荐