常温固化氟涂料具有卓越的性能。
The normal temperature solidified fluoro - coating has outstanding advantages.
介绍了常温固化含氟聚氨酯涂料的研究进展。
The paper introduced the technical progress in air curing fluorinated polyurethane coatings.
讨论了常温固化型有机氟树脂在合成过程中的影响因素。
This paper discusses the factors influencing the synthesis of room temperature cured organo-fluoride resin.
以环氧E-20为基料，加入二硫化钼、氧化铝为填料的一种常温固化耐磨防腐涂层。
The room temperature cured abrasion resistant anticorrosive coatings is prepared with E-20 epoxy as binder and molybdenum disulfide and aluminum oxide as fillers.
该涂料可常温固化、耐磨、防滑、耐油、及耐一般化学药品腐蚀、耐洗刷，可湿面施工。
The coating is abrasion resistant, anti-skid, oil resistant, chemical resistant, and washing-proof. It can be applied on wet surface construction and cured in room temperature.
研究了热固性不饱和聚酯常温固化制造新型塑料电热板的配方、成型工艺路线与成型条件。
A new pattern plastic galvanothermy board can be made by solidifying heat set unsaturated polyester resin at normal temperature.
四川省绵阳市联星化工公司新建的尿素造粒塔选用了常温固化型氟碳漆对其内外壁进行了防腐涂装。
Room temperature cured fluorocarbon coating was applied as anti-corrosion coat in newly built urea prilling tower of Lianxing Chemical company, Mianyang city, Sichuan province, China.
本文讨论了常温固化不饱和聚酯树脂浇涛体的拉伸强度、拉伸模量、断裂延伸率与固化度之间的关系。
In this paper, the relation of tensile strength, tensile modulus and breaking elongation of unsaturated polyester casting matrix cured at room temperature to curing degree was discussed.
本论文对常温固化型胶粘剂间苯二酚PRF和高分子异氰酸酯API落叶松集成材的胶合工艺技术进行了研究。
This paper focuses on the research of bonding technology of Chinese Larch Glulam (glued-laminated timber) with Phenol resorcinol formaldehyde(PRF) and Aqueous polymer Isocyanate(API)adhesives.
论述了几种氟聚合物涂料，如水性氟聚合物涂料、粉末氟聚合物涂料和低温或常温固化氟聚合物涂料的开发动向。
The developing trends of fluoropolymer coatings, such as water soluble fluoropolymer coatings powder fluoropolymer coatings and low or room temperature curable fluoropolymer coatings.
可在常温下固化成型。
并用该树脂与固化剂、惰性添料配制了胶泥，测试了其常温、热处理及腐蚀后的胶泥的力学性能、腐蚀率及焦化时间。
The dynamic performance, corrosion rate and coking time of the mortar were tested under normal temperature and after heat treatment and corrosion individually.
在没有活化剂存在和常温常压条件下，即使经过长时间的水浸，无机非金属材料也不会凝胶和固化。
In the absence of activator existence and normal temperature and pressure conditions, even after a long period of flooding, inorganic non-metallic materials will not gel and cure.
该共聚物可用于配制常温或烘烤固化的涂料。
The copolymer can be used for preparing the room-temperature or baking and curing coatings.
在常温下涂布后直接紫外光交联固化，考察了光引发剂、交联剂、光固化时间等因素对UV固化压敏胶综合性能的影响。
The influences of photoinitiator, crosslinking agent and cure time on the properties of UV curing pressure sensitive adhesive were discussed in the paper.
树脂固化速度与温度有关，温度越高固化就越快，在常温下约为一小时。
Resin curing speed bears a relation with the temperature, the higher temperature, the quicker curing, and it spends about one hour for curing under normal temperature.
试验结果表明该胶粘剂常温可固化；在施工中不产生毒性烟雾，不影响操作人员的健康；
The experimental results show that the adhesive cures at room temperature, no toxic vapour is produced in the application, so it does not affect workers' health.
试验结果表明该胶粘剂常温可固化；在施工中不产生毒性烟雾，不影响操作人员的健康；
The experimental results show that the adhesive cures at room temperature, no toxic vapour is produced in the application, so it does not affect workers' health.
应用推荐