警告：一个以上带电电路。
必须能够防止电击以及接触危险的带电电路。
They must be protected from electric shock and contact with hazardous live circuits.
这个概念是，当被击中时，金属弹丸使两个带电板块撞起，形成一回电路和释放的电力脉冲，这可以打碎弹头了。
The idea is that when hit, the metal in a projectile shorts the two charged plates together, forming a circuit and releasing a surge of electricity which can break the warhead up.
带电物体接近被测电路的输入端时，就会发生静电耦合和干扰。
Electrostatic coupling or interference occurs when an electrically charged object approaches the input circuit under test.
继电器是保护系统的逻辑元件，它感知故障，并使断路器解扣电路带电和断路器打开触点。
Relays are the logic elements of a protection system which sense the fault and cause the circuit-breaker trip circuits to be energized and the breakers to open their contacts.
短路短路通常是指带电流的组件之间意外的电路连接。
Short circuit a short circuit is generally an unintended electrical connection between current carrying parts.
现代半导体集成电路的制造往往要求涉及大电流低能量带电搀杂剂原子的注入步骤。
The fabrication of modern semiconducting integrated circuits often requires implantation steps that involve high currents of low-energy charged dopant atoms.
一般是由于带电拔插系统中接插件，或电路中电源对地之间短路而引起，此时可采用静态电阻测量法。
General is due to the live system connector plug or circuit between the power-to-ground short-circuit caused by, at this point resistance measurement method can be static.
根据SF_6断路器运行过程中的实际情况，设计了相应的硬件电路和软件算法，以期较为准确地对带电运行状态下的SF_6断路器进行在线监测。
According to the practical operation situation of SF6 circuit breaker, the hardware circuit and the software arithmetic are designed to intend to accurately monitor the SF6 circuit breaker in service.
最后给出集中参数电路和微带电路的E类放大器实例。
At last, several class E amplifiers with lumped element and microstrip circuit are given.
将微带电路向空间的辐射作为一个端口来处理，成功地消除了由于忽略电路的空间辐射效应引入的电路数字模拟误差。
The errors caused by omiting of electromagnetic radiations of opened microstrip in numerical simulating of microstrip circuits is eliminated successfully by making one circuit port of the radiation.
切角贴片在微带电路中得到了大量的应用。
Patches with corner cut are widely used in microstrip circuits.
电路设计还避免了接触器触点带电闭合。
Also, charged contact problem with the contactor is relieved.
并以宽带电流反馈运算放大器为核心，辅以FET输入电路及程控电路构建了高速高输入阻抗可变增益放大电路。
Combined with wide band current feedback amplifier, FET input circuit and programmable circuit, variable gain amplification circuit with high speed and high input impedance is designed.
由控制电路实现焊接程序的控制，带电枢电压负反馈的调速电路控制和调节送丝速度。
The control to welding procedure is realized by a control circuit, and wire feed rate is regulated and controlled by speed governing circuit with the armature voltage negative feedback.
被测件放在测试夹具里，如二极管、晶体管、微带电路等。
DUT is placed in test fixture such as diode, transistors, microstrip circuit and so on.
采用新型光源与电路系统，并在结构上可实现带电维修。
The new-developed lamp with new lighting source and circuit system can be maintained with electricity.
介绍了利用微带电路来确定一组高性能、高频印刷电路板材料的介电常数和损耗角正切的方法，且给出了一组印刷电路板材料的特性测量值。
The paper introduces measurements about dielectric constant and tangential loss angle of a group of good function and high frequency printed electronic circuit plate with microstrip circuit.
特别是亚波长结构的引入，使微带电路呈现出了前所未有的特性，如慢波特性、左手特性等。
In particular the introduction of sub-wavelength structures, the microstrip circuit has presented unprecedented features, such as slow-wave characteristics, left-handed properties and so on.
然而，该系统没有附带电路原理图，损坏后维修难度较大。
But because of lack of additional circuit diagrams, it is difficult to repair if the power is damaged.
接着对系统进行了顶层设计并逐步细化，最终完成了基带电路板的制作与调试。
In the design phase, a whole Top-Down analysis and module design was done, and finally the circuit of the Baseband module was realized and tested.
从实际电路出发，对低压供电系统中零线带电现象进行了分析，得出零线带电的四种原因。
This paper investigates the phenomenon of electrification of zero conductor in low voltage power supply system on the basis of actual circuit, and suggests sollutions for four possible causes.
根据“虚短”和“虚断”的特点，可得到电路的通带电压放大倍数和通带截止频率。
According to "virtual short" and "virtual-off" feature, available to the circuit passband voltage gain and pass-band cut-off frequency.
硬件设计部门主要手机产品硬件部分的设计、开发工作。包括基带电路的设计、调试。射频电路的设计、调试。PCB布线。生产支持等相关工作。需招聘如下人员。
HW Dept. is responsible for hardware design of mobile phone, including Baseband design, RF design, PCB layout, production support, Etc. Now we need the below people.
本文方法对微带电路及微带天线的CAD设计将具有实际意义。
This new technique can be used as a powerful CAD tool in the analysis of planar microstrip circuits and microstrip antennas.
另外，论文还对微带电路的一种混合FDTD算法进行了研究。
The transition algorithm between the traditional FDTD and a new online FDTD is investigated.
利用微带电路作成的行波管外平衡器的理论研究和实验工作已经完成。
Theoretical and experimental research have been done for external TWT equalizer by using microstrip circuit.
介绍了运用FDTD设计和分析微带电路和天线的基础理论，分析了误差产生的原因。
The finite difference time domain (FDTD) method applied to simulate microwave circuits and antennas is presented in this paper. The computational errors have been analysed.
介绍了运用FDTD设计和分析微带电路和天线的基础理论，分析了误差产生的原因。
The finite difference time domain (FDTD) method applied to simulate microwave circuits and antennas is presented in this paper. The computational errors have been analysed.
应用推荐