本文描述了在设备上进行HIP致密化机制研究、HIP工艺参数的设计与选择、包套的研究等工作的必要性和可行性。
This paper describes the necessity and feasibility for studying HIP densification mechanism, designing and optimizing process parameters and capsules using this equipment.
通过客车舱门包边模具的设计与应用，实现了侧舱门制作工艺上的突破。
Through the design and application of wrapping die of bus port, the processing technology of side port is broken through.
设计了铜包铝线的前处理方案、镀铜工艺，并分析了其作用机理。
Front treatment and copper plated program of copper plated aluminium wire were designed, and its mechanism was analysed.
介绍复合包敷层厚壁固体药柱的X射线检验透照工艺的设计和检测结果的评价。
The evaluation on the X - ray inspection technology and test results for the composite coaling thick - wall solid charge is described in the paper.
本文叙述了猪软面革公文包的设计与制作，工艺。
This paper described the productive process of portfolio made by pigskin soft leather.
论述了影响油包水乳化体系稳定性的因素、油包水的配方设计原则以及油包水的生产工艺的控制和调整，并介绍了有利凯玛公司的油包水乳化剂。
Introduce the different factors and principle in the formulation and process of water in oil emulsion system. The water in oil emulsifiers produced in Uniqema are also introduced.
方法：采用均匀设计与正交试验法，以外观评分和包封率评分为指标，综合分析试验结果来确定制备工艺条件。
METHODS: Taking the score of appearance and the score of drug embedding ratio as indexes, the technical conditions were determined by uniform design and orthogonal test.
文摘：通过水力学模拟六流连铸中间包后发现，原设计的中间包在夹杂物的上浮及温度的均匀性方面还存在不足，不能很好地满足生产工艺要求。
Abstract: Water modeling of the six-strand caster tundish shows that the original design of the tundish can not meet the technical requirements for inclusion floatation and temperature homogenization.
以微囊包封率、粒径和形态为评价指标，通过正交设计确定克拉霉素微囊的最佳制备工艺。
Using Orthogonal Design Method to optimize the preparation technique by using encapsulation rate, particle size and shape as evaluating index.
从变形原理入手，分析了产生鼓包的原因，着重从原料、工艺布局和轧辊孔型设计等方面提出了解决鼓包的一些方法。
In the paper the cause for the said bulging is analyzed with the deformation theory. Also proposed are certain solutions for the problem, involving the material, process arrangement and roll...
本发明涉及一种电镀弱包镶金刚石钻头或工具及其制作工艺。所用的金刚石为JR4型、粒度为60/70-80/100目，设计的金刚石体积浓度为14％-22％；
An electroplated drill bit inlaid by diamond features that said diamond is JR4 type and has 60/70-80/100 meshes and 14-22% of volume concentration.
本发明涉及一种电镀弱包镶金刚石钻头或工具及其制作工艺。所用的金刚石为JR4型、粒度为60/70-80/100目，设计的金刚石体积浓度为14％-22％；
An electroplated drill bit inlaid by diamond features that said diamond is JR4 type and has 60/70-80/100 meshes and 14-22% of volume concentration.
应用推荐