接着，启动工作循环。
第二个工作循环开始后，模具闭合。
自动工作循环周期为一分钟。
发动机的进气过程是发动机工作循环的关键所在。
The intake process is the key part to the working circle of the engine.
排气过程：压缩气体移到排气口，完成一个工作循环。
Exhaust process: compressed gases to the exhaust port, to complete a working cycle.
为设计计算工作循环，建立了该模型结构子层的数学模型。
A math model of the sub structure level is built to calculate the work cycle.
PLC通过其存贮的工艺参数完成丝光机相应的工作循环。
The PLC completes the corresponding cycle through the stored technique parameters.
四冲程发动机的工作循环是以活塞在上止点、进气门打开为开始的。
The cycle of operation of the four-stoke engine begins with the piston at TDC and the intake valve open.
本文介绍了用8031单片机控制立式拉床的工作循环和速度选择等。
The paper presents the work cycle and velocity election of a vertical broacher controled with single chip microcomputer 8031.
每种阀门类型中列出的标准工作循环都可以升级成所示的更大的循环。
Standard duty cycles are listed for each valve type and are upgradeable to extended cycles as indicated.
通过对丸药实时检测方法和途径的分析探讨，提出了完整的工作循环模式。
With analysis of the way of pills inspection, an integrated work cycle mode was given out.
工作循环的升级备选件采用更大的电机来避免长期运转而造成热量的累积。
Upgrades in duty cycles use heavier motors to handle heat built up from extended operation.
往复式压缩机工作时会产生大量的热，因此在工作循环之间需要设定冷却过程。
Reciprocating compressors can produce the work a lot of heat, so in working circulation cooling process between need to set.
在工作循环的第三个冲程开始，活塞再次位于上止点，曲轴已经旋转了一整周。
At the beginning of the third stroke of the cycle of operations, the piston is once again at TDC, the crankshaft having turned through one full revolution.
活塞往复一次，各吸入和排出一次液体，称为一个工作循环；这种泵称为单动泵。
A reciprocating piston, the inhalation and from a liquid, known as a working cycle; this pump known as the single-action pump.
设计计算机械工作循环的实质是协调各执行机构运动区段的逻辑关系和时序关系。
The essence of designing the work cycle is to coordinate the logic dependency among the motion sections of each mechanism.
通过对高炉冶炼工艺及上料系统工作循环过程的研究，设计开发了高炉上料控制系统。
The blast furnace feeding control system is designed by studying the technics of blast furnace smelting and the circulation of feeding.
发动机的一个工作循环分布在活塞的四个行程中，一个完整的工作循环曲轴需要转动两圈。
The cycle of operations is spread over four piston strokes. To complete the full cycle it takes two revolutions of the crankshaft.
“由于与其他类型的混合动力车一起，高效的益处在极大程度上依赖这些车辆的“工作循环”，”亚当斯说。
“As with other types of hybrids, the efficiency benefits are heavily dependent on the vehicles’ duty cycle, ” Adams said.
“由于与其他类型的混合动力车一起，高效的益处在极大程度上依赖这些车辆的“工作循环”，”亚当斯说。
"As with other types of hybrids, the efficiency benefits are heavily dependent on the vehicles' duty cycle," Adams said.
应用比例技术能使电液信号转换过程可控，采用比例阀可以方便、快捷、精确地完成工作循环过程。
The procedure of electric and hydraulic signal exchange can be controlled by the application of proportional technique, and work circle can be fulfilled conveniently, rapidly and accurately.
该器件尤其适合那些需要极其精确的工作循环控制或精确的边缘检测(如汽车凸轮轴感测)的应用。
This device is particularly suited to those applications that require extremely accurate duty cycle control or accurate edge-detection, such as automotive camshaft sensing.
如果发动机完成一个工作循环，只需要两个行程，就称为两冲程循环发动机，或者简称两冲程发动机。
If it needs only two strokes to complete a cycle, it is called a two-stroke cycle engine or, for short, a two-cycle engine.
本文从燃烧室压力、系统工作循环方式以及最大推力三个方面叙述了世界各国液体火箭发动机的技术水平。
This paper presents the development of the liquid propellant rocket engine technology from the viewpoint of combustion chamber pressure, thrust level and power cycle.
类似项目50米跨（单线，1/5悬臂）没有使用蒸汽养生和预制钢筋笼，一个工作循环为10-12天。
On similar projects, with 50m span length (single spans, cantilevering 1/5), the cycle time is usually approx. 10 - 12 days without steam curing, reinforced in-situ by hand.
文中介绍了空压机的有关技术参数和基本结构、各子系统工作循环，以便提高工作人员对空压机的操作水平。
The paper introduced the technical parameters, basic structure and work cycle of each subsystem of air compressor with the aim to improve the operation level of workers.
通过操作面板选择，不仅可实现定程、定压两种成形工艺，而且可实现有垫、无垫、顶出三种工艺工作循环。
Through the operation panel, not only can realize the fixed distance and constant pressure of two kinds of forming process, and can realize a pad, pad free, top three cycle process.
通常只有当遇到需要额外工作负载时，工作循环才会大于25%，如阀门处于节流状态或驱动大型蝶阀的应用场合。
Duty cycles greater than 25% are generally needed only when additional work loads are encountered, such as valve modulation or in actuation of larger butterfly valves.
通常只有当遇到需要额外工作负载时，工作循环才会大于25%，如阀门处于节流状态或驱动大型蝶阀的应用场合。
Duty cycles greater than 25% are generally needed only when additional work loads are encountered, such as valve modulation or in actuation of larger butterfly valves.
应用推荐