内置H型钢混凝土组合结构是实现套建增层的结构设计形式之一。
Prestressed composite concrete beam with encased H-steel is one of the structural design forms for the outer-jacketing structure for adding story.
本文从直接增层方案和外套结构增层方案两方面，论述了建筑物增层的结构设计方案及要求。
This paper states structure design scheme of architecture adding-floor from two aspects of direct adding and adding a floor at out structure.
在结构设计参数常用取值范围内，对不设纵隔板和设置纵隔板两种常用钢桥面铺装层的结构设计指标关键影响因素进行正交敏感性分析。
Within regular range of structural design parameters, the key factors of design indices are studied through orthogonal analysis of steel bridge deck surfacing with or without longitudinal clapboard.
针对垃圾卫生填埋场防渗层的设计，介绍了膨润土、高密度聚乙烯膜和一些新型防渗材料的种类和性质，及单层防渗层、复合防渗层的结构设计。
This paper introduced the styles and characteristics of bentonite, HDPE and some new impervious materials, and the structural designs of the liner and composite in sanitary landfill.
如果你把架构设计好了，把云计算结构设计正确了，再加上你的开发层设计对了，你就可以构建这些平台。
That if you can get the architecture right, this cloud-computing architecture, if you can get the development layers right, you can build these platforms.
分析了影响松套层绞式adss光缆结构设计的诸要素，探讨光缆结构设计方法，并给出了光缆的设计实例。
This paper explores the construction design of loose tube layer stranded ADSS cables by analysing the affecting factors and gives example for cable design.
100米高的高层建筑结构设计(约32层)要求竖框放置，每隔8层高与钢梁连接。
The design of a 100 m tall high rise structure (approx. 32 storeys) calls for erecting portal frames connected with steel girders placed every 8 storeys.
本文介绍了手糊成型玻璃钢圆柱形容器的结构设计，并对内衬层成型工艺提出了改进方法。
The structure design of cylindrical tank with hand lay-up process were introduced, the improved method of liner forming process were provided.
分析了空调面板框的结构特点及工艺要求，介绍了叠层式注射模的结构、工作过程以及结构设计要点。
Through the technological analysis of the air condition panel, we introduced the structure principle of the stack injection mold for the air condition panel for designing the mold.
介绍6度抗震设防下11层钢结构住宅的结构设计，对该工程的结构体系选用、节点构造作了一些研究工作。
It introduces the structure design of an 11-storey steel residence on 6 degree earthquake resistance, the selection of structure system and node construction of it.
本文就消能减震结构设计参数，即消能部件的支撑刚度、层间最大阻尼力与结构层间屈服力比值等恢复力模型参数的选取进行了讨论。
The design curves of equivalent damping ratio to the brace stiffness, and ratio of maximum damping force of the damping device to the inter-story yield shear force of the structure are proposed.
为了研究深厚冲积层井简的支护技术，引入竖向附加力，进行井壁结构设计。
For the sake of researching shoring technology in the profundity alluvium, introduced Vertical additional Force and devising well structure.
计算结果符合结构设计规范的要求，可以为半硬式平流层飞艇的结构设计提供参考。
The simulation result comply with the specifications of structure design well, and a reference for semi-rigid structure of the stratospheric airship was provided.
探讨了强约束钢筋混凝土柱、结构转换层、预应力混凝土结构等技术在高层建筑结构设计中的应用。
The technological applications of the strongly confined reinforced concrete column and the transformation story in the tall building design and prestressed concrete are discussed in the paper.
层间位移限值是钢筋混凝土超高层结构设计中的一个重要参数。
The limit value of interstory drift is an important parameter for the design of reinforced concrete super highrise buildings.
并给出箱形转换层结构设计的有关建议。
Concerned Suggestions about structure design of box transfer story are presented.
结合瑞通广场的结构设计，阐述了逆向结构转换层区别于一般转换层的受力特点。
According to the example of Ruitong Plaza structure design, this paper focus on the difference of load transfer mechanism between reverse transfer story and common transfer story.
最后基于分层设计思想，将平台划分为全局配置层、数据接口层、业务逻辑处理层和页面层四个层次，完成了系统开发平台的结构设计。
Finally, the platform is divided into common configuration layer, data access layer, logic operation layer, and display layer with the layered design.
将薄层抗弹陶瓷材料与树脂基复合材料通过仿生结构设计制备了软、硬相交替叠合的多层增韧贝壳珍珠层结构仿生复合材料。
The multilayer toughening conch nacre structure bio-inspired ballistic resistant composites which consisted of thin layer ceramic and resin matrix composites were prepared.
结合农场工程施工经验，提出了水工钢闸门聚酯玻璃钢复合防腐层结构设计、施工工艺及质量标准，为该工艺的推广应用提供了一定的参考依据。
Based on the construction experience in farm engineerings, the structure design, constructing process and quality standard for the combined anti-corrosion layers were presented. That provides...
聚酯玻璃钢胶衣层的技术特性与要求；并对聚酯玻璃钢抗水泡结构设计进行了探讨。
The technical characteristics and requirements of gel coat for UP resin, the design of anti-blistering for structure design are also introduced.
反射裂缝是加铺层结构设计考虑的重点。
Reflective cracking overlay structure is the focus of design considerations.
其次是合理的结构设计，旨在使各结构层的层位与厚度达到理想的程度。
Secondly, the structure design must be rationalized. All of them could meet every structural layer to get the ideal...
如何研究随机参数层合板响应的统计特性，这对正确估计结构设计的可靠性有着非常重要的意义。
The study of statistical properties response of random parameter laminated plates plays an important role in the right estimation of the reliability of construction design.
广州名盛广场工程，采用全逆作法施工钢结构设计方案，并且将路桥工程采用的大跨度拱形钢桁架结构应用于房建工程的转换层结构，这是一种新的尝试。
This article discusses a successful application of the big span steel structure truss assemble prefabricated parts and slip technology in Qingdao Liuting International Airport project phase II.
具体作了以下一些工作：1本文针对3种不同开间、柱距、平面布置形式的建筑套型，考虑不同抗震设防要求，进行常见的6层、12层、18层住宅的结构设计分析。
The detail is in the below: 1 Structural design analysis of steel structure residence at the story of 6, 12, 18 is made under 3 kinds of suite pattern considering different earthquake design levels.
具体作了以下一些工作：1本文针对3种不同开间、柱距、平面布置形式的建筑套型，考虑不同抗震设防要求，进行常见的6层、12层、18层住宅的结构设计分析。
The detail is in the below: 1 Structural design analysis of steel structure residence at the story of 6, 12, 18 is made under 3 kinds of suite pattern considering different earthquake design levels.
应用推荐