备用尾轴的螺纹部分涂漆了吗？
Is the threaded portion of the spare tailshaft well coated with paint?
你能把尾轴上的标记指给我看吗？
请检查一下尾轴锥形部分。
轴的尾轴承安装顺序如何？
尾轴管轴承塑料喷漆。
所以对螺旋桨尾轴进行蠕变分析是十分有意义的。
So it is significative to carry out a research on room temperature creep characteristic of propeller shaft .
通过分析得出：主减速器尾轴输出处存在故障征兆。
Through analysis, we could see output of tail shaft in main reducing gear has failure symptom.
因此，船舶尾轴架结构的优化设计是一个很重要的问题。
Therefore, the optimizing of propeller shaft bracket is a very important issue.
分析尾轴架的动刚度曲线，可得到尾轴架结构的固有频率。
Analyses of these curves make the natural frequencies of the shaft brackets available.
本文根据尾轴密封装置的工作实际，提出一种新的传热模型。
Based on the practical operating condition of the stern tube sealing system, a new model of heat transfer is presented in this paper.
船舶尾轴的辛泼来克司密封环形状非常复杂，用一般方法难以进行分析。
The shape of the Simplex stern tube seal ring is so complicated that its characters can not be analysed by ordinary methods.
全系列产品均可以匹配齿轮箱销售，部分机型可以连带尾轴，螺旋桨销售。
All Marine engines could be sold with gearbox, and some engines could be sold with tail shaft and propeller.
首先要镗孔，然后安装尾轴管，接下来装炮铜或白合金制的轴承套，也叫轴承。
First you need the boring for the shaft, then install the stern tube into the stern frame, next fit the gun-metal or white-metal bush.
本文结合实例介绍了一种安全、可靠、省时、省钱的纠正尾轴弯曲超差的方法。
With a number of examples the paper introduces a safe, reliable, easy and cost-effective method for correcting stern shaft deflection.
从分析船舶尾轴架结构特点入手，介绍尾轴架工艺计算、工艺编制、产品生产过程及经验。
Starting from analyzing the structural properties of the Marine propeller shaft bracket, the authors introduce the technology calculation, design, process and their production experience.
采用实验方法对某舰尾轴架进行动刚度测量，得到了前尾轴架和后尾轴架的横向动刚度曲线。
In the paper, the transverse dynamic stiffness curves of front shaft bracket and back shaft bracket of a ship were obtained by means of experiments.
下部装置——包括下部机壳、进料口、尾轴装配、张紧装置，并有旋转探测仪、料位开关供选配。
Lower device ~ lower casing, charger inlet, tail shaft assembly, tensioner, and with optional rotary detector and level switch.
某舰的螺旋桨尾轴长期处在恒定载荷作用下，虽然尾轴应力在弹性极限范围内，但是尾轴局部还是很容易发生微量的塑性变形。
Tiny deformation will appear in the local of the propeller shaft of certain ship which is endured an invariableness load, although the shaft stress is within the elastic limit range.
同时就尾旋中偏滚对尾旋侧滑的影响、绕铅垂轴旋转对坡度的影响等进行了讨论分析。
Meanwhile, it also discusses the influence of roll yaw on sideslip in spin, and of moving round plumb line on Angle of bank.
在Z- 80单板机的控制下，可将一轴成千上万米长的细丝从头至尾进行逐点测量。
Under the control of a Z-80 single board computer, a spool of fine thread up to ten thousand meters can be measured point by point and from end to end.
潜水艇采用单轴四尾舵。
The submarine has four stern rudder with a single large shaft.
介绍了添加絮凝剂的全粒级尾砂充填料强度试验，由试验得出了三个龄期的单轴抗压强度方程。
The strength of unclassified failing fills containing flocculants was tested and equations of uniaxial compressive strength for three curing periods were derived.
在双轴式涡轮喷气发动机中，及级涡轮导向器面积和尾喷口面积匹配关系影响到发动机工作稳定性、可靠性和性能。
The stability, reliability and performance of two spool turbojet engine will be affected by the matching correlation between 1st and 2nd turbine nozzle areas and engine nozzle area.
转子自由尾迹模型的基础上开发的计算方法为水平轴风力发电机的空气动力性能的预测。
A computational method based on rotor free-wake model was developed for horizontal axis wind turbine's aerodynamic performance prediction.
利用单斜丝热线旋转进行水平轴风力机模型的尾迹流场测量。
The panel method was used to predict the wake flow field of propeller.
利用单斜丝热线旋转进行水平轴风力机模型的尾迹流场测量。
The panel method was used to predict the wake flow field of propeller.
应用推荐