本文以阶梯形铸件对铸钢件进行了悬浮浇注实验，研究了悬浮剂加入量对铸件凝固特性的影响。
In this paper the experiments of suspension pouring of steel castings are carried out with step casting samples.
实验证明，镁锆铬质浇注料的抗渣侵蚀能力、抗渣渗透能力较高。
The experiment results show that the resistance of magnesia-zircon-chrome castable to corrosion and penetration of slag are higher.
筒类铸件连铸实验中，浇注方法很重要。
The pouring method is very important in the continuous casting experiment.
实验测定了化学成分、浇注温度、铸件模数和铸型刚度对球墨铸铁收缩特性的影响。
The effects of casting modulus, pouring temperature. carbon equivalent and mould toughness on the solidification shrinkage of ductile cast iron was investigated experimentally.
优化实验后，制备出系列高性能高尔夫球型高铝空心球保温浇注料。
After the optimization of experiment, the golf-shaped bubble bauxite insulating castables with high performance were prepared.
在实验室条件下采用浇注的混凝土试件代替岩石进行爆破实验，然后应用提出的方法进行了分维数计算。
The casting concrete test piece is used to carry out blasting experiment under laboratory conditions, and then calculations are conducted using fore-mentioned approaches.
通过一系列实验室试验，垫补浇注料可认为是较好的罐底耐火材料。
Through a series of laboratory experiment, padding castable is considered to be good as refractory for the ladle bottom.
同时，采用静态坩埚法进行了抗渣性实验，研究了矾土基高铝-尖晶石浇注料抗渣性能的变化规律。
Slag resistance experiment was carried out adopting static crucible method, and change regulation of slag resistance performance of high alumina bauxite based-spinel castable was also studied.
通过对比实验的方法，研究了不经过和经过电磁泵处理的铝合金液浇注流动性试样。
Using the method of compare experiment, the samples of liquid al alloy with and without treatment by electromagnetic pump were studied respectively.
实验结果表明：提高浇注时复合试样的整体温度有利于获得界面的冶金结合。
The result shows improving complex sample's temperature is good to gain metallurgical bonding interface.
通过浇注料试样性能检测比较，探讨了不同种类结合剂对浇注料性能的影响，实验证明复合结合剂更有利于浇注料性能的提高。
The effects of different binders on the castable were discussed by the comparison of castable samples properties from testing results. The experimental resul...
利用水模拟实验研究连铸浇注操作工艺(参数)对板坯结晶器内液面涡流的影响规律。
The experiment of water model has been conducted to study the effect of pouring technical parameters on the surface flow and vortex in the mold of continuous casting of slab.
实验结果表明：在其他工艺参数一定时，浇注温度、铸型温度变化对压铸镁合金AM60B组织与性能有较大的影响；
The result of experiment shows that, at constant value of other factors, the changes of pouring and mold temperature have greater effects on microstructure and properties of AM60B alloy;
本实验采用SEM和EDAX研究了各段带的显微结构和基质组成，讨论了转炉终渣对浇注料的侵蚀过程和机理。
The changes in the microstructure and matrix composition of every zone have been investigated by using SEM and EDAX. Also the process and mechanism of slag corrosion have been discussed.
本实验采用SEM和EDAX研究了各段带的显微结构和基质组成，讨论了转炉终渣对浇注料的侵蚀过程和机理。
The changes in the microstructure and matrix composition of every zone have been investigated by using SEM and EDAX. Also the process and mechanism of slag corrosion have been discussed.
应用推荐