给出了圆板试件应力热图经图象处理和计算的定量分析结果。
The result of quantitative analysis of the circular plate specimen stress pattern processed and calculated is given.
定量及SEM分析表明，焊缝中表面只残留少量锌，在焊缝两侧的热影响区，锌层厚度呈梯度分布。
Through quantitative and SEM analysis, the minim zinc was found remaining on the surface of weld and the zinc thickness on the heat-affected zones appeared gradient.
应用热弹塑性有限元法对液力变矩器点固焊过程夹持力和焊接变形进行全面分析，定量得出了焊接预留间隙，为夹具设计提供了依据。
According to the analysis results, pre-welding gap was gained quantitatively, which can be regarded as warrants and references for the design of welding clamps.
本文全面分析了各因素对对流换热系数精度的影响，并进行了定量分析。
The influence of various parameters on the measuring accuracy of the convective heat-transfer coefficient was analyzed quantitatively.
我们能够更进一步定量分析二倍频减少的程度，来 评估雷射后剩馀热伤害的程度。
Furthermore, the degree of collagen damage in the residual thermal zone was evaluated by quantitative analysis of second harmonic generation signals.
前刀面热损伤层的定量分析，可以为随动磨削的加工余量提供理论依据。
The analysis of thermal damage layer for the rake face can provide theoretical guidances for confirming the machining allowance of surface grinding.
针对以往空间热环境分析模型的不足，在遥感、地理信息系统支持下，创建了基于人工神经网络和遗传算法的城市热环境非线性定量分析模型。
With the support of GIS and RS, efforts were made to develop a quantitative analysis model of urban spatial thermal environment based on genetic algorithms back propagation and genetic algorithms.
以此为基础，在景观尺度上定量分析研究区内亚高山带水热条件与森林和亚高山草甸植被分布格局的关系。
Furthermore, the relationship between vegetation distribution pattern and the above factors in the study area was analyzed by ANOVA at the landscape scale.
前言： 研究了差热定量分析面积法的准确性和不同物料样品粒度对定性差热分析的影响。
The essay discusses the accuracy of area method of thermal quantitative analysis and the effect of sample particle size with different materials on thermal analysis.
结合长期热环境下肿瘤生长的实验数据，对该过程中肿瘤系统内可能的熵变进行了半定量和定性分析。
The results show that the long-term hyperthermia environment can increase the positive entropy of the system and finally inhabit the growth of tumor.
本文采用定量相分析法测定灰砂系统水热反应的水化物，并通过SEM观察及试块强度测定等研究了灰砂系统水热反应动力学。
Kinetics of hydrothermal reaction in lime-sand system was investigated by means of quantitative phase analysis, SEM observation, and compressive strength measurement.
后刀面热损伤层的定量分析，可以为确定最小刃磨余量提供理论支持。
The study of thermal damage layer for the major flank can provide theoretical guidances for determining the minimum machining allowance of edge grinding.
本文从节能角度出发，定量地分析了加热器无水位运行对火电厂热经济性的影响。
From the point of view of energy-saving, this peper gives a quantitive analysis of the impact of no-water-level operation of feedwater heaters on the economic performance of power plants.
利用背散射电子衍射取向成像技术定量分析了热模拟单向压缩条件下Q235碳素钢热变形时铁素体的织构形成规律。
The textural features during ferrite refinement by deformation enhanced transformation were analyzed by means of orientation mapping based on the EBSD technique in a Q235 low carbon steel.
溶解度、二维NOE和等温滴定量热法的分析结果说明，包裹作用和静电相互作用共同造成保泰松的溶解度提高。
Evidence from the solubility, 2D-NOESY results and ITC analysis suggest that encapsulation and electrostatic interaction together caused the solubility enhancement of phenylbutazone.
在试验研究的基础上，对辐向油道上下线饼表面热流密度对换热的影响进行了定量分析。
Based on the tests and researches, the effects of the surface heat flow density of sections in the radial oil ducts on the heat exchange are analyzed quantitatively.
本文研究的主题是“分形论定量金相分析技术及其在热壁加氢反应器寿命分析中的应用”。
This paper focuses on the technology of fractal quantitative metallography and its application on remaining life …
据此可定量、简便、直观地对SP赛预热器的换热情况进行热力学分析，并为热利用的改善指明方向。
Therefore, the thermodynamic analysis for heat exchange in a preheater of SP kiln is given quantitatively, conveniently and directly, and the direction for improving the energy utilization is al…
对辛硫磷在气相色谱分析过程中因热分解产生的分解产物进行定性与定量研究。
The decomposed products of phoxim in process of gas chromatography were identified and studied.
利用背散射电子衍射取向成像技术定量分析了热模拟单向压缩条件下Q235碳素钢热变形时铁素体的织构形成规律。
The texture evolution of ferrite during warm compression of Q235 low carbon steel was determined quantitatively by means of orientation mapping based on the EBSD technique.
方法：采用动态比浊定量法考察注射用HGF对鲎试剂的干扰作用并与热原检查法进行对比试验分析。
METHODS the interference function of HGF to TAL was investigated precisely by turbidimetric technique, and the results were compared with pyrogen method.
此外，还研究了焊接热输入量对局部脆性区断裂韧性的影响，并通过定性、定量的金相显微组织评定对试验结果进行了分析。
In addition, the effect of welding heat input was studied. Qualitative and quantitative metallographic examination of the simulated microstructures was made to assist t...
目前，运用火灾模拟程序进行定量计算，分析失火隧道内的温度、烟气生成量等参数时，都是以火灾热释放率(HRR)为基础的。
At present, in order to analyse the temperature and smoke in the tunnel fire, we use numerical simulation to calculate the variable, which are all based on the fire heat release rate (HRR).
目前，运用火灾模拟程序进行定量计算，分析失火隧道内的温度、烟气生成量等参数时，都是以火灾热释放率(HRR)为基础的。
At present, in order to analyse the temperature and smoke in the tunnel fire, we use numerical simulation to calculate the variable, which are all based on the fire heat release rate (HRR).
应用推荐