得到了三种复合材料界面层的抗拉强度。
The tensile strength of three filled composites was measured.
探讨了接枝聚合物层对复合材料界面的影响。
The influence of carbon fiber surface grafting polymerization on the interface of polymer composite is also discussed.
脱粘是纤维增强复合材料界面裂纹扩展的主要表现形式。
Debonding is a main form of interfacial crack growth of fiber-reinforced composites.
单纤维拔出实验是研究纤维复合材料界面性能的重要方法。
Single fibre pull-out test is one of the important ways to study the properties of fiber-reinforced composites 'interface.
借助扫描电镜、显微硬度分析了复合材料界面结构及力学性能。
By means of scanning electron microscope and micro-hardness, the interfacial structure and mechanical properties of the metal composite were analyzed.
研究了纤维增强脆性基复合材料界面脱粘过程中剪应力的变化规律。
The interfacial shear stress of a brittle composite matrix that reinforced with fibers is studied.
研究了不同渗流时间和渗流温度对非晶复合材料界面反应的影响规律。
The influence of infiltration temperature and time on the interface reaction was investigated.
用边界元方法对横向载荷作用下纤维增强复合材料界面的滑移进行分析。
A boundary element method for the analysis of interfacial slip in fiber-reinforced composites under transverse loading is presented.
单纤维段裂试验作为复合材料界面剪切强度的一种测试方法被沿用至今。
The single fiber fragmentation test has been used to determine the interfacial shear strength of composite materials.
单纤维段裂试验作为复合材料界面剪切强度的一种测试方法被沿用至今。
The interfacial shear strength (IFSS) between fibers and resin was measured by the microbond test.
这样，显然，复合材料界面上的纤维与基体的粘接是复合材料失效的基础。
It becomes clear, then, that adhesion of the fiber and the matrix at the composite interface is fundamental to the failure of the composite.
用两种会聚束电子衍射(CBED)技术研究了复合材料界面残余应变场。
The residual strain fields at composites interface were studied with two convergent beam electron diffraction (CBED) techniques.
在此基础上，对聚合物水泥基复合材料界面粘结层的结构模型进行了描述。
Based on the investigation results, the structure model of the interfacial bond layer in polymer cement based composite materials is described.
也介绍了单涂层、双涂层及复合涂层对金属基复合材料界面及性能的影响。
Effects of single coatings, double coatings and complex coatings on the interface and properties of metal matrix composites are also introduced.
当循环上限应力超过一定程度后，振动处理会对复合材料界面造成一定损伤。
The damage for the interface of composite can be induced by the vibratory treatment when the maximum cycling stress exceeds certain extent.
同时通过实验结果分析，阐明阳极氧化处理使复合材料界面性能改善的机理。
Meanwhile the mechanism of the anodic oxidation treatment to improve the interfacial property of composites is obtained by analyzing the results.
复合材料界面结构由芯材扩散层、激冷凝固层、方向性生长层和胞状晶粒层组成。
The interface structure of composite consists of core material diffusion layer, chilling solidified layer, directional growth layer, and cellular granular layer.
研究由平头压痕蠕变试验来确定纤维复合材料界面影响区蠕变性能参数的可行性。
This paper discusses the possibility of determining the creep parameters oon the interlayer zone of reinforced composites by indentation test method.
综述了增强相涂层种类、涂层制备方法及其对金属基复合材料界面和性能的影响。
Coatings on reinforcements, fabrication methods of the coatings and their effects on the interface and properties of metal matrix composites are reviewed.
采用力调制原子力显微镜及扫描电镜的线扫描功能对复合材料界面相精细结构进行分析。
Force modulation atomic force microscope and linear scanning system of scanning electron microscope were carried out to analyze the microstructure of composite interface.
本文综述了聚合物基纤维复合材料界面残余应力的形成、测定方法和各种理论分析方法。
In this paper, an overview of the formation, determination and various theoretical analysis methods of residual stress at the fiber - polymer interface is presented.
本文综述了聚合物基纤维复合材料界面残余热应力的形成、测定方法和各种理论分析方法。
In this paper an overview of the formation, determination and various theoretical analysis methods of residual stress on the fiber-polymer interface is presented.
此外，断口形貌的SEM观察表明，随保温时间的延长或热压压力的提高，复合材料界面层变厚。
The SEM fractographs show that the composite interfacial films between the fibre and the matrix are thickened with the increase of the hot-pressing time or pressures.
实验结果证明，芳纶表面改性显著提高了其复合材料界面的粘结强度，相反却降低了其界面断裂能。
The results show that the interfacial adhesion strength increased noticeably for composites of active aramid fiber but the fracture energy of the interface decreased.
冯青。典型湿热条件碳纤维复合材料界面性能衰减规律研究。北京：北京航空航天大学，2010。
Feng Qing. Research on the attenuation law of interfacial properties of carbon fiber reinforced composites under typical hygrothermal conditions. Beijing: Beihang University, 2010.
本文介绍了编织增强体液体成型技术、原材料的选择，并对其成型的复合材料界面作了较系统的分析。
This paper introduces weaving reinforcement liquid composite molding technology and choice of raw materials and analyses systematically the composites interface.
文章分析了复合材料界面控制研究的现状，介绍了为释放复合材料界面处的热应力应采取的相关措施。
The studies on composites interface controlling are analyzed. The measures are introduced to release the heat stress in the interface.
主要介绍了国内外木塑复合材料界面相容剂的分类及其在复合材料中的应用、表征等方面的研究进展。
In this article the classification of the interfacial compatibilizer for WPC and the progress in studies of applications and characterization on it are presented.
主要介绍了国内外木塑复合材料界面相容剂的分类及其在复合材料中的应用、表征等方面的研究进展。
In this article the classification of the interfacial compatibilizer for WPC and the progress in studies of applications and characterization on it are presented.
应用推荐