壳体试验的试验温度、试验介质、试验压力、试验持续最短时间及允许渗漏率见表。
Testing temperature. Testing medium. Testing pressure. The shortest continued time and allowed leak rate on shell test and seal function test as following sheet.
通过热态浇注试验，得到了质量良好的铝合金壳体铸件。
Good quality aluminium-alloy shell casting I produced by pouring test.
RA108 赛车的设计保证所有关键领域都符合国际汽联的安全规则，并且防撞结构满足碰撞试验的要求，例如：前鼻椎、单壳体车身和尾部防撞结构。
The design of the RA108 ensures that all key areas comply with the FIA safety regulations and crash test requirements for the impact structures, such as the nose, monocoque and rear impact structure.
有限元分析与实际试验结果具有很好的一致性，为该壳体结构的设计改进提供了理论依据。
The analysis agrees quite well with the results of real test, which provides theory support for improving of case design.
拱坝的应力分析方法包括纯拱法、拱梁分载法、有限元法、壳体理论计算方法和结构模型试验法。
The stress analytic method of arch dam covers pure arch method, arch beam sharing method, finite element method, calculating method of shell theory and structural model test method.
本文用振动试验建模的方法来探索旋转壳体的干、湿模态参数及其非线性振动特性。
By using the method of establishing model through vibration test, this paper discusses the rotatory shell's dry-humid mode parameters and its non-linear vibration properties.
通过试验和生产验证，所焊接的后桥壳体精度高、抗疲劳性能好、质量稳定。
The result of welding experiment and production practice show that the welded rear-axle housing have quality stability and high precision and fatigue strength.
潜水电机壳体，包括机架，尾轴承架，法兰和罩盖总装，必须采用符合美国材料试验协会ASTM A - 48类别30标准的、密实的铸铁或更好的材料制造。
The submersible motor enclosure including frame, end brackets, flanges and cap assembly shall be constructed of close-grained cast iron, ASTM A-48, Class 30 or better.
利用模型试验研究了大型圆柱形壳体与法兰对接环形焊缝的焊接变形。
Welding deformations due to circumferential welds at the joint between the large cylindrical shell and the flange is studied by model test.
采用光学显微镜和扫描电镜等试验手段分析了某裂解器加热器壳体出现开裂的原因。
The reasons for cracking of a cracker heater shell had been revealed with the aid of optical microscope and scanning electron microscope et al.
论述球铁高压燃气闸阀的概况、设计要点、壳体浇铸工艺性的改进和试验方法。
The general description, main points of design, technological improvements in valve body casting and test methods of the said valve are discussed.
为考核纤维增强攻坚战斗部在混凝土中的爆炸毁伤效应，对裸装药、复合材料壳体、钢壳体装药在混凝土靶中的爆炸破坏效应进行了对比试验研究。
Experimental investigation on the blast effect of naked explosive, explosive charge covered with composite material shell as well as with steel shell in the concrete target is described.
采用有限元法模拟曲面壳体热拉深成形，并进行成形工艺试验，其模拟结果与试验结果一致。
A curved surface shell hot drawing was simulateel by finite element method and forming trial was condncted.
通过试验测量其壳体应力、层间间隙、衬里环向应变来评价复合效果。
The effect of the compound figuration is then evaluated by measuring the shell stress, the layer gap and the lining circumferential strain during the hydraulic bulge.
试验结果表明，采用合适的工艺，微弧氧化表面处理完全可以满足汽车壳体类零件的抗腐蚀性能要求。
The results showed that the surface treatment of micro-arc oxidation can fully meet the requirements of corrosion resistance for automobile housing under proper technical condition.
试验结果表明，采用合适的工艺，微弧氧化表面处理完全可以满足汽车壳体类零件的抗腐蚀性能要求。
The results showed that the surface treatment of micro-arc oxidation can fully meet the requirements of corrosion resistance for automobile housing under proper technical condition.
应用推荐