镀银，镀锡，氟塑料绝缘安装电线。
这些电线由一个塑料绝缘层缠了起来。
然后在它们的外面覆盖一层塑料绝缘物质。
They are then covered in another layer of plastic insulation.
然后在其上覆盖一层塑料绝缘膜，以及另一层黄金薄膜。
That was followed by a layer of plastic insulator, and another layer of gold.
氟塑料绝缘和护套的电缆应不小于电缆外径的8倍。
It is not less than 8 times the outer diameter of the cable for fluoroplastic insulated and sheathed control cable.
氟塑料绝缘和硅橡胶护套的电缆应小于电缆外径的6倍。
It is not less than 6 times the outer diameter of the cable for fluoroplastic insulated and silicone rubber sheathed control cable.
本产品按GB9330《塑料绝缘控制电缆》及企业标准制造。
This product is manufactured according to GB9330 and enterprise standards.
当你将电缆穿孔时，电缆在两个金属锯齿中下沉，这样就将电缆的塑料绝缘套剥离。
As you punch it down, the cable descends between the two metal teeth, which remove its plastic insulation (it's called insulation displacement) and the cable is cut.
使用该插座，当插销接触到电源时。插销的铜片和塑料绝缘部分已进入防护框内。能有效地防止触电事故。
When the socket is used, and a pin contacts a power, the copper sheet and the plastic insulating part of the pin enter the guard frame, which can effectively prevent the accident of electric shock.
直流电压试验作为一种对油浸纸绝缘电缆非常有效的方法应用至今，但它对塑料绝缘电缆是无效而且有害的。
The DC test, which is an effective means for the diagnostics of oil impregnated paper insulated cable, is still used even now, but it is ineffective and harmful for the plastic insulated cable.
塑料合成树脂被广泛应用到各种产品中，包括电线的绝缘层。
The plastic resin is used in a wide range of products, including electrical wire insulation.
聚合物太阳能板不同于如聚乙烯等大多数商用塑料，其本质上是绝缘体。
Polymer solar panels differ from most commercial plastics like polythene which are essentially insulators.
它的外部由etfe氟塑料覆盖，这层氟塑料即构成内部结构又作为内部的绝缘层。
The exterior is covered in ETFE cushions, which provides both structure and insulation for the interior.
该中心电极1.0的世界粮食理事会已与薄胶塑料布覆盖，因此要得到完全绝缘阴极。
The center electrode of the WFC v1.0 has been covered with a thin adhesive plastic sheet so has to get a fully insulated cathod.
所述的带有弹性的绝缘套管采用硅胶套管、橡胶套管或塑料套管。
The insulating sleeve with the elasticity adopts a silicone tube, a rubber sleeve or a plastic sleeve.
主要利用塑料材料本身的绝缘、密度小、无电磁干扰、耐腐蚀、防水等性能，从而实现其对螺丝的保护作用。
The main use of plastic material itself insulation, small density, no electromagnetic interference, corrosion resistance, waterproof performance, so as to realize its protective effects on screw.
帽子是用运送海鲜的白色聚苯乙烯泡沫塑料箱做成的，这种材料的绝缘性好，质地又轻。
These were made from the kind of white Styrofoam plastic boxes which are widely used to transport fresh seafood due to their insulating properties and light weight.
特富龙、聚乙烯和蓝宝石是高质量绝缘材料的例子，但要避免使用酚醛塑料和尼龙等材料。
Teflon, polyethylene, and sapphire are examples of good quality insulators, but avoid materials like phenolics and nylon.
聚苯乙烯泡沫塑料应被用于保护绝缘。
介绍了树脂基导热复合材料的导热机理，重点介绍高耐热、高刚性热塑性树脂基复合导热绝缘塑料的制备。
The thermal conducting mechanism and the methods of preparation of insulating and thermal conductive plastics were briefly introduced.
公开了一种用于将绝缘底层涂料不连续地应用于碳纤维增强塑料（CFRP）部件的系统及方法。
Systems and methods for discontinuously applying an insulating primer to a carbon fiber reinforced plastic (CFRP) component are disclosed.
尽管早期对塑料电缆寄予希望，但对于较高电压，最有效的绝缘仍采用油纸组合绝缘。
In spite of earlier hopes for plastic insulations, the combination of paper and oil still forms the most effective dielectric at the higher voltages.
用途：可作涂料、油漆、油墨、橡胶、塑料、绝缘带的填充剂。
Usage: can be used for coatings, paints, inks, rubber, plastics, insulation filler zone.
PVC是涂层导线的最普遍的塑料，因为它在费用是相对地低的，韧性，阻燃并且拥有好绝缘物产。
PVC is the most popular plastic for coating wires, as it is relatively low in cost, resilient, fire retardant and possesses good insulating properties.
绝缘的最好是喷沫塑料。
通过聚苯硫醚（PPS）与大颗粒氧化镁（40~325目） 混合经双螺杆挤出机挤出造粒制备了导热绝缘塑料。
Thermal conductive insulating PPS plastics were made by extrusion compounding PPS with MgO particles of large particle sizeBF(40~325-mesh)BFQ.
由于其无毒、无味、优良的密封性、绝缘性、耐腐性，被广泛应用于水处理、天然气、化工、塑料、电子工程等领域。
Due to its non-toxic, tasteless, good sealing, insulation, corrosion resistance, are widely used in water treatment, gas, chemical, plastic, electronic engineering and other fields.
介绍了在一定用途的绝缘聚合物上加适量导电填料（导电炭黑）生产导电塑料与导电硅橡胶弹体等导电聚合材料的方法。
The method to produce the polymerized material such as conductive plastic and conductive silicon rubber by adding the conductive material (mainly the carbon black) is introduced.
介绍了在一定用途的绝缘聚合物上加适量导电填料（导电炭黑）生产导电塑料与导电硅橡胶弹体等导电聚合材料的方法。
The method to produce the polymerized material such as conductive plastic and conductive silicon rubber by adding the conductive material (mainly the carbon black) is introduced.
应用推荐