冷轧扭钢筋在检测时,试样易在夹具内断裂,其塑性难以精确测定。
When testing, it is more likely for cold-rolled and twisted steel bar to be broken in fixture and so that its plasticity can hardly be precisely measured.
通过测定不同新拌水泥浆体的剪切应力、屈服应力、塑性粘度等流变参数,绘制流变曲线,分析含不同高效减水剂的新拌水泥浆体的触变性。
Mapping rheogram and analyzing thixotropy of fresh cement paste with different superplasticizers by measuring the rheologic parameters such as shearing stress, yield stress and plastic viscosity.
结合蠕变试验结果,研究和分析了三种测定蠕变塑性伸长率的方法。
Combine with the creep experimental results, the three methods for measure plastic percentage elongation of creep are studied and analysed.
本研究采用热扭转法测定和比较了铸态与轧态高速钢的热塑性特征曲线。
A hot torsion test was used in this study for measuring and comparing the hot plasticity curve of as-cast and hot rolled HSS.
通过对出生前有慢性应激经历子代海马CA 1区LTP和LTD诱导性及学习记忆和行为反应的测定,探讨出生前慢性应激对子代海马CA 1区突触可塑性及学习记忆行为的影响。
We explored the effects of prenatal stress on hippocampal synaptic plasticity and behavior of the offspring by testing LTP and LTD in hippocampal CA1 area and learning and memory in Morris Water Maze.
用计算机技术和传感技术组成系统构成型砂多项性能测试仪,测定湿型粘土砂塑性变形临界值。
Critical value of plastic deformation of green sand has been tested by molding sand multi-tester using computer and sensors.
通过坯料可塑性和干燥性能的测定,对有机粘结剂进行了筛选。
The organic binder was selected by detection of plasticity and drying property of the body.
本文引入金属塑性变形传播概念,利用光弹法测定了两种钢的塑性变形传播速度。
The plastic deformation propagation speeds of steels are determined by using photo-elastic coating and high speed photography method.
提出了一种测定热塑性丁苯橡胶(SBS)颗粒样品物理性能的制片方法。
A method of measuring thermoplastic styrene-butadiene rubber SBS (simply called SBS) crumb sample's physical performance is introduced.
表观粘度测定显示辛烯基琥珀酸淀粉酯具有剪切变稀现象,属于假塑性流体,表观黏度随着温度升高而下降。
The phenomenon of increasing shear force, and decreasing apparent viscosity, showed that it was a kind of Pseudo plastic Fluid. As the temperature increased, the apparent viscosity decreased.
测定了九龙高岭土的可塑性、化学组成、粒度及其分布、白度等,并且做了X—射线和透射电子显微镜分析。
The plasticity, chemical composition, particle size and its distribution, whiteness and so on of jiulong kaolin were measured and analyzed by X-ray and TEM.
用于测定氨纶丝断裂强度、断裂伸长率、定伸长负荷、应力松弛,塑性变形等性能指标。
Used for testing indexes of polyurethane monofilament, such as breaking tenacity, elongation at break, load at specified elongation, relaxation of stress, plastic deformation, etc.
范围本标准对混凝土压塑性指数的测定方法(在预计的坍落度小于10mm,并且骨料的标称粒径不超过40 mm的情况下)作出了规定。
SCOPE This Standard sets out the method for determining the compactibility index, for concrete, where the expected slump is less than 10 mm and the nominal size of aggregate does not exceed 40 mm.
2附录4 测定钢性非热塑性塑料材料的防火性的测试方法(附录4)。
UIC564-2 Appendix 4: Test method for detemining the fire resistance of rigid non-thermoplastic materials.
提出了一种用微弯曲实验测定材料的与应变梯度塑性相联系的内禀长度的新方法。
Therefore, it is necessary to establish new constitutive models—strain gradient plasticity theories which possess the intrinsic material length.
开裂应力测定装置测试了水泥砂浆、混凝土塑性抗拉强度和塑性收缩开裂应力。
The paper states that the plastic cracks after shaped the pumping concreting divides into plastic settlement crack and plastic shrinkage crack.
开裂应力测定装置测试了水泥砂浆、混凝土塑性抗拉强度和塑性收缩开裂应力。
The paper states that the plastic cracks after shaped the pumping concreting divides into plastic settlement crack and plastic shrinkage crack.
应用推荐