这些，现在来了，两个基本尺寸。
由关系式计算最佳凸轮机构的基本尺寸。
According to the relational expression, the basic size of CAM mechanism can be defined.
此部分内容给出整车基本尺寸，请检修时对比参考。
This part of contents indicates the basic size of vehicle, please overhaul according to the reference.
当宽容是从两个方向的基本尺寸，它被称为双边公差。
When the tolerance is in both directions from the basic size, it is known as a bilateral tolerance.
现有按许用压力角确定凸轮机构基本尺寸的方法欠妥。
The available method for determining basic size of cam mechanism according to its allowable pressure angle is lack of appropriateness.
利用薄材加热和冷却公式设计计算出烘房的基本尺寸。
Use the heating and cooling formula for thin material to design the dimensions of iron printing dryer.
下偏差：零件最小极限尺寸减去其基本尺寸所得的差值。
Lower deviation: the difference between the minimum permissible size of a part and its basic size.
根据对木片切料角的工艺要求可初步确定削片机的基本尺寸。
According to the technological requirement of wood chip cropping Angle, the basic size of chipper could be determined.
分析了摆动从动件盘形凸轮机构的压力角与基本尺寸之间的关系。
The relationship of cam with oscillating followers pressure angle and radius of basic circle were analyzed.
分析了摆动从动件盘形凸轮机构的压力角与基本尺寸之间的关系。
The relationship of CAM with oscillating follower's pressure Angle and Basic dimensions were analyzed.
对任何给定的基本尺寸，公差范围和偏差可以相对于被称为零线的零偏差线来确定。
For any given basic size, a range of tolerances and deviations may be specified with respect to the line of zero deviation, called the zero line.
几个精度要求较高的尺寸，因其公差值较小，所以编程时没有取均匀值，而取其基本尺寸。
A few higher accuracy, because of its size smaller values of tolerance, so when programming haven't taken even value, and take its basic size.
零件强度校核中，首先选择危险零件，根据ADAMS建模基本尺寸，利用PROE对零件进行建模。
In the process of intensity check of parts, we choose the dangerous parts first. According to the basic size of the model in ADAMS, we establish a model based on PROE.
其次拟定坝的基本尺寸，包括坝坡、坝顶高程、坝顶宽度以及防渗体及排水设备、护坡等的尺寸，使之满足土石坝的工作要求。
Then, you can decide the basic sizes, including those of slope, crest el, crest width, anti-seepage, drainage, protecting slope, and etc.
以MATLAB为辅助工具，给出了直动推杆盘形凸轮机构在推杆实现规律的基本运动时的基本尺寸优化设计方法，使凸轮机构的体积和最大压力角达到最小。
A method for optimizing the main dimensions of a cam-oscillating follower mechanism in common follower motions is presented with the MATLAB, which maximizes the CAM volume and maximum pressure angles.
若你是在这个尺寸范围内寻购帆船，那你应该学习了解一下龙骨的这些基本类型之间的差别。
If you are shopping for a sailboat in this range, you should understand the differences between these fundamental types of keels.
与真正行星相仿，灶神星的尺寸（直径大约为520公里）和密度使其具备足够的引力保持基本的球体形状。
Vesta’s size (it is around 520km in diameter) and density make it massive enough for its gravity to keep it roughly spherical, like a proper planet.
pl 与 worldCompositeMap.pl程序非常相似 ——其修改主要是在把各种注释组件与各种尺寸的基本图像对齐。
stateCompositeMap.pl is very similar to the worldCompositeMap.pl program -- its modifications are focused on aligning the various annotation components to the differently sized base image.
由于涉及的风力和帆面的动态原理，一艘单桅帆船基本上总是相近尺寸的帆船中最快的，尤其是逆风行驶时。
Because of the wind and sail dynamics involved, a sloop is almost always faster than other RIGS in boats of comparable size, especially when sailing to windward.
栅格单元是你在页面上放置文本和图片的基本坐标。它决定的是“放置”而非“尺寸”。
Grid units are the primary locations on your page where you will place text and images.
自调心球轴承的基本设计带有一圆柱孔，或者在某些尺寸范围内带一圆锥孔（圆锥1：12）。
The basic design self-aligning ball bearing is available with a cylindrical bore or, in certain size ranges, with a tapered bore (taper 1:12).
换句话说，基本额定动载荷提供了一个基于丝杠类型和尺寸来计算寿命的基础。
In other words, the Basic Dynamic Load Rating provides a basis of Life Calculations based on the size and type of ball screws.
与真正行星相仿，灶神星的尺寸和密度使其具备足够的引力保持基本的球体形状。
Vesta's size and density make it massive enough for its gravity to keep it roughly spherical, like a proper planet.
对一个工件最基本的说明其形式和尺寸的方法就是告知通过刀刃对材料的除去量。
The primary method of imparting form and dimension to a workpiece is the removal of material by the use of edged cutting tools.
电动机基本技术要求符合IEC34 - 1和GB755国际和国家标准要求，安装尺寸符合IEC72国际标准。
The basic technical requirements conform to the international IEC34-1 standard and national GB755 standard, and the mounting dimensions conform to the international IEC72 standard.
尽管武器类型和尺寸各不相同，但把光束增强为致命能量束的基本爆能技术是简便且大致相同的。
The basic blaster technology of intensifying a beam of light into a deadly bolt is scalable, and largely the same despite the differences in weapon types and sizes.
尽管武器类型和尺寸各不相同，但把光束增强为致命能量束的基本爆能技术是简便且大致相同的。
The basic blaster technology of intensifying a beam of light into a deadly bolt is scalable, and largely the same despite the differences in weapon types and sizes.
应用推荐