有人忘记带来把麦克风夹在支杆上的U型螺栓。
Somebody forgot to bring along the U-bolts to clamp the microphones to the pole.
由车轴拆下螺帽，U型螺栓和弹簧支架。
型螺栓-不锈钢材质，可以适用任何型号的导轨。
T bolt will work with any rails type. Made of stainless steel.
铁路混凝土桥梁人行道上的U型螺栓，在使用一段时期后容易出现断裂病害。
The U-shaped bolts embedded in concrete beam are split after using a period of time.
夹具用T型螺栓固定于铣床工作台，同时与工作台上的槽接合（图13.3）。
The fixture is secured to the machine table with T-bolts, also engaging in the slots in the table (Fig. 13.3).
扭剪型螺栓破断沟槽的加工采用数控技术、提高沟槽加工精度，确保配套质量；
Adopting the computerized Numerical Control Technique to machine the breakage groove of torshear type bolts can improve the machining precision of groove, guarantee the assembled quality.
产品包括：螺栓、螺钉、螺柱、U型螺栓、预装配的螺钉和垫片组件以及与预装配组件一样加工的无垫圈产品。
Products included are bolts, screws, studs, U-bolts, preassembled screw and washer assemblies (sems), and products manufactured the same as sems except without washer.
钢结构系列：钢结构用高强度大六角头螺栓，扭剪型螺栓连接副，钢网架球节点用高强度螺栓，焊钉，钻尾丝等。
Steel Series: steel with high strength large hexagon head bolts, torsion shear bolt connections made, the steel truss joints of high strength bolts, studs, drill the end of wire.
高强度螺栓、钢结构螺栓、外六角螺栓、内六角螺栓、地角螺栓、双头螺栓、U型螺栓和电力铁塔螺栓、油井上用的各种专用螺栓。
Different types of products include high strength bolts, hex bolts, hex socket head cap screws, foundation bolts, stud bolts, U bolts, bolts for electric power steel tower, bolts for oil well, etc.
结合桥梁—人行道系统的现场振动测试和螺栓试样断口分析结果，指出既有桥上发生的U型螺栓破断属于疲劳破坏，并提出了改进意见。
Some in-site vibrating test and metal fracture analysis have been done to reveal that the crack of the U-shaped bolts is fatigue failure and some reference for designer is put forward.
原件日下午12 / 12型冲锋枪功能的单独的手动安全和消防模式选择，无论是在形式的跨螺栓按钮了。
Original PM 12 / Model 12 submachine guns featured separate manual safety and fire mode selector, both being made in the form of the cross-bolt buttons.
首选应用是轴承结构，包括滚珠和轴套。还有，它也能用来做刀具、针形阀、球型止回阀、阀门基座、泵零件、球头螺栓、轴套、抗磨损纺织机械。
In addition, it should be considered for cutlery, needle valves, ball check valves, valve seats, pump parts, ball studs, bushings, and wear-resistant textile components.
以DF7C型内燃机车锻件中的杯形零件之一——气缸螺栓保护螺母为例，进行温挤压工艺研究，并据此设计出了成形模具。
Taking cylinder nut-protected bolt, one of the cup-shaped parts in the forging parts of DF7C gas engine, as an example, the warm extruding is researched, accordingly, the forming die is designed.
本文讨论了承压型高强度螺栓连接在同时承受剪力和杆轴方向拉力时其计算公式的应用。
This paper discusses the application of calculation formulas of high strength bolt connection in bearing type under the action of both shearing force and axial tensile force.
KP1型矩形条孔烧结页岩多孔砖砌体墙上应采用空心砌体专用膨胀螺栓，因其能够形成可靠的“自螺母效应”。
In KP1 type perforated brick masonry, expansion bolt especially design for perforated brick is prefer, because it can form "self- anchor" effect and hold tightly in brick hole.
介绍了太脱拉T815型汽车后桥从动圆锥齿轮联接螺栓发生断裂的原因、现象和解决方法。
This paper describes the causes, appearance and remedy of fractured fastening bolts in driven bevel gear of TATRA model T815 truck rear axle.
本文论述具有预紧力的承压型高强度螺栓接头静力承载能力。
This paper studies the statically bearing capacity of the fasteners with high-strength bolts possessing pretension on the shear.
型钳夹车的端盖及其连接螺栓的强度直接影响D _(38)型钳夹车的使用安全。
Strengths of the end shield and its fixed bolt of D38 schnabel car affect the car's utility and safety.
对10级BY型防松螺母当前运用中存在的个别螺栓折断和螺母松动问题进行了分析探讨，并提出了相应的措施与建议。
The breaking of very few bolts and loosening of nuts existing in the present operation of 10 Grade BY Type check nuts are analyzed and discussed.
将主机全部线条板，U型垫块(线条板需安装调整螺栓)，放置到机组旁边以便主机安装时使用。
Put all line plates and U-shaped filling blocks of the unit beside the engine, so they can be used conveniently later. The line plates shall be fitted with adjustable bolts.
介绍无螺栓自固衬板及燕尾形耐磨铸钢小衬瓦在DT M型球磨机上的应用效果。
Introduces the applying results of free bolt self-standing welt and coattail antiwear cast steel tiny lining tile in type of DTM ball crusher.
对检测中发现的ST型缓冲器拉紧螺栓折断、螺母脱落问题进行了分析，并提出了改进建议。
The problems of breaking of the drag bolts and falling off of the nuts on ST draft gears found in the inspection are analyzed. And suggestions for improvement are given.
通过对游梁式抽油机对接式连杆下接头连接螺栓的失效分析，指出了采用双螺母防松时，将薄型螺母放置在外侧是不恰当的。
Through the failure analysis of connecting bolt of down rod, it points out that it is not correct to put the thinner nut outer side if the double nut anti-loose method is adopted.
分析HXD1型机车牵引座的螺栓连接方式中的特殊点及其机理，并通过受力计算说明了衬套对螺栓使用可靠性的影响。
This paper analyses the special points and mechanism of bolt connection mode on type HXD1 locomotive traction base, and shows the effect of bush to bolt application reliability by stress calculation.
对检测中发现的ST型缓冲器拉紧螺栓折断、螺母脱落问题进行了分析，并提出了改进建议。
The problems of breaking of the drag bolts and falling off of the nuts on ST draft gears found in the inspection are analyzed.
减速器专用T型基础螺栓；
本文通过三组不同试件的试验，对磨擦型和承压型两种高度螺栓连接形式的工作机理和失效形式进行了试验研究。
Based on the experiment of three different groups of samples the working principle and the failure types of the friction connection and the bearing connection high strength bolt were studied.
不锈钢螺栓，螺柱型，六角形驱动套节。
大六角头高强度螺栓连接副扭矩系数的检测，扭剪型高强度螺栓连接副坚固预拉力的检测，高强度螺栓连接磨擦面抗滑移系数的检测，是钢结构材料验收中的重要测量。
To determine the anti-slip coefficient of the high-strength bolt which connects components of friction surface, it is screwed and determined by torsion and tensile testing machines respectively.
翼缘法兰螺栓应为双头螺栓，螺纹为全长型，内径600mm或以下的法兰的螺栓至少为m 16，内径600 mm以上的法兰的螺栓至少为m 20。
Girth flange bolting shall be of stud bolt type, threaded full length, and at least M16 for flange of 600 mm and smaller inside diameter and at least M20 for over 600 mm inside diameter flange.
应用推荐