它实际上是创造替代水准折坯体读者。
It is actually created as alternative to the standard pack adobe reader.
它创造替代水准折坯体读者。
It is created as alternative to the standard pack adobe reader.
介绍了液相浸渍炭纤维坯体的两种方法。
Two Methods: Used to liquid impregnate carbon fiber preform are introduced.
介绍了液相浸渍炭纤维坯体的两种方法。
Two methods used to liquid impregnate carbon fiber preform are introduced.
用料浆喷涂法在Q235钢基体上成形覆层坯体；
The green body was formed by slurry spray method on the Q235 steel substrate.
坯体开裂的可能性主要与坯体厚度和干燥速率有关。
The probability of cracking is mostly related to the thickness of the tape and rate of drying.
如果你想多创造充分汲取图片坯体插画可为您选择。
If you wish to draw more than creating full pictures, Adobe Illustrator may be the choice for you.
预制坯体的纤维体积含量选为25％至30％为最好。
The proper fibre volume fraction of original is between 25% and 30%.
它是在计算机控制下多层打印逐层叠加制出三维陶瓷坯体。
The three dimensional ceramic body is made by sacking layers of printing ceramic ink.
粉料经预模压后冷等静压成型，能得到均匀致密的陶瓷坯体。
The ceramic green was shaped by pressing and cold isostatic pressure, then an uniform and compact ceramic green was produced.
注：你一定有你的计算机产品坯体读者您看过这份文件的命令。
Note: you must have the Adobe Reader product on your computer in order for you to read this document.
硅灰石在陶瓷中的应用，大多是作为陶瓷坯体的主要原料使用。
The wollastonite in ceramics application, mostly is takes the ceramic body the primary data use.
在陶瓷坯体干燥过程中，温度的检测与控制是个很重要的环节。
During the process of the tile drying, the temperature detecting and controlling is very important.
固相质量分数和引发剂质量分数都会影响坯体的线性收缩率和密度。
Both solid volume fraction and dispersant volume fraction had some effects on shrinkage and density of green body.
根据实验现象对颗粒涂层过程和坯体的致密化过程进行了详细探讨。
Particles coating process and sintering process of the compact was discussed according to experiment results.
本文分析了陶瓷砂轮成型后坯体的缺陷以及由缺陷产生裂纹的机理。
In this paper, analysis is made on different defects of wheel green piece and the cracks formed whereby.
结果表明，球磨处理和粉体煅烧温度对HA坯体的烧结行为均有明显影响。
The results showed that ball-milling treatment and calcining temperature exert an influence on sintering process of HA.
电子探针线扫描分析的结果表明，红色陶衣中铁的含量明显高于内部坯体。
The results of linear SEM-EDS indicated that the content of iron in the red pottery coating was remarkably higher than that in the inner adobe of pottery.
利用这两种成型技术可以获得均匀、无密度梯度的近净尺寸坯体和致密陶瓷制品。
With the two methods the homogenous green bodies without density gradient and high density sintered ceramic bodies can be gained.
采用一种新型的真空凝胶注模成型法，减少了在凝胶注模成型时坯体中形成的气泡。
A new vacuum gel-casting was applied to ceramics which could reduce the air bubbles formed during the casting in the green body.
用压汞法测定了离心成形坯体的孔隙率，曲线呈窄的单峰分布，证明了粉体无团聚。
The results show that the distribution curves are one-humped and concentric, which indicates that the powders have no agglomeration.
采用有限单元法计算了反射镜坯体的热残余应力，通过对比验证了测试结果可靠性。
The thermal residual stress was calculated by the finite element method. Both testing and calculation data proved the reliability of testing data.
陶瓷坯体具有尺寸变化率小，密度较高且均匀，足够的脱模强度，表面质量好等特点。
The ceramic green body is characterized by little dimensional change rate, high green body density, high homogeneity, sufficient strength for demoulding and good green body surface quality.
硅灰石作为碱土金属硅酸盐，在普通陶瓷坯体中起助熔的作用，降低坯体的烧结温度。
The wollastonite as the alkali earth metal silicate, helps the melt in the ordinary ceramic body the function, reduces the body the agglutination temperature.
本文介绍透辉石在坯体中的作用以及在陶瓷釉面砖坯体中的应用。确定透辉石的用量。
This paper discussed the act and application of diopside in the body of ceramic wall tiles. The appropriate amount of diopside in the recipes was given.
添加多磷酸钠和含磷成分可以降低泥浆的粘度，提高坯体的排浆速度，缩短干燥时间。
The slip viscosity can be reduced, the slip exhausting speed of bodies can be increased, and their drying cycle can be shortened, adding the sodium polyphosphate and phosphorus components.
坯体具有足够的脱模强度、较高的密度均匀性和合适的孔隙率以及尺寸变化率小等特点。
The composite green body is characterized by sufficient strength for demoulding, high density homogeneity, appropriate porosity and little dimensional change rate.
自制了聚丙烯酸钠复合坯体增强剂，研究了它对陶瓷坯体强度和地砖生产成品率的影响。
Compound ceramic body reinforcing agent with sodium polyacrylate was prepared and its effects on the strength of ceramics body and rate of finished product of floor tiles were studied.
在陶瓷材料先进成型技术中，凝胶注模成型是制备大尺寸、复杂形状坯体的一种有效方法。
Gelcasting is one of the most promising methods among all the advanced ceramic forming techniques.
在陶瓷材料先进成型技术中，凝胶注模成型是制备大尺寸、复杂形状坯体的一种有效方法。
Gelcasting is one of the most promising methods among all the advanced ceramic forming techniques.
应用推荐