该数据加载和读取电路生成地址信号。
Address signals are generated by the data loading and reading circuitry.
控制芯片存储关于存储芯片是否正常工作的信息，并根据地址信号选择正常工作的芯片。
The control chips store the information that whether the storage chips work normally or not, and select normal working chip based on address signals.
所述块修复选择器响应于单元块地址信号输出块修复选择信号，以用另外的单元块替换所述缺陷单元块。
The block repair selector outputs a block repair selection signal for replacing the defective cell block with another cell block in response to a cell block address signal.
另一示例是，与LUT相关的以其他方式不需要的寄存器可被用于为用户RAM模式提供同步读地址信号。
As another example, an otherwise unneeded register associated with a LUT can be used to provide a synchronous read address signal for user RAM mode.
在调试信号时，需要查看的一些重要寄存器包括GPR、指令指针(NIP)、机器状态寄存器(MSR)、Trap、数据地址寄存器(DAR)等等。
Important registers to look for when debugging through signals are the GPRs, instruction pointer (NIP), machine state register (MSR), trap, data address register (DAR), and so on.
与遵循树的自然结构而进行的地址转换不同，机器上的任何设备都可以发起和终止中断信号。
Unlike address range translation which follows the natural structure of the tree, Interrupt signals can originate from and terminate on any device in a machine.
在通信中，地址就是指选择信号中指明呼叫目的的部分。
In communications, address is the part of the selection signals that indicates the destination of a call.
此时write系统调用会被进程接收到的SIGBUS信号中断，因为当前进程访问了非法内存地址。
Your write system call will be interrupted by the bus error signal SIGBUS, because you performed a bad memory access.
该数据包括客户端的IP地址及其检测到的任何信号塔或是WiFi结点。
This data includes the client's IP address and information about any cell towers or WiFi nodes it can detect.
总线是连接计算机各部件的一簇公共信号线，由地址总线、数据总线和控制总线组成。
The bus is the computer parts connected by a bunch of public signal, address bus, data bus and control bus composition.
并通过CPU和刷新地址电路共享存储器的方法，对系统输出的校验信号的波形进行编程。
Hz. The waveform of the correcting signal outputted from the system is coded with CPU and address modification circuits sharing the same memory.
它从存储器中取指令，提供存储器需要的地址和控制信号。
It fetches instructions from memory, supplying the address and control signals needed by memory to access its data.
其中的视频同步信号生成电路以及视频图像数据地址生成电路采用了PLD器件，这样就可以很方便地去改变视频制式，也便于调试。
PLD is used to produce the video synchronization signal and the logical address of the video image. So it is very convenient to change the forms of the video and easy to debug!
每种微处理机都具有三组总线，分别供数据、地址和控制信号使用。
Each standard microprocessing unit creates three buses: one each for data, address, and control.
路灯故障时，可发出声光报警信号，并显示故障路灯地址编号。
When the lamp failed to light, it may be audible and visual alarm signals and display street address of fault ones.
本文提出的几乎最佳二元阵列偶与几乎最佳三元阵列偶的构造方法为最佳离散信号的设计提供了更广的地址码选择范围。
The constructions of the almost perfect binary arrays pairs and the almost perfect ternary arrays pairs provide broader choice range of the address yard.
比如，信号强度变化时，地址簿仍能访问。
For example, the address book can be accessed while the signal strength changes.
数字可设定地址的光界面- - -第206部分：控制开关专门要求- - -从数字信号转化为d.c。电压(设备类型5)。
Digital addressable lighting interface - Part 206: Particular requirements for control gear - Conversion from digital signal into d. c. voltage (device type 5).
下载图像后，会向垃圾电子邮件的发件人发送Web信号通知，告知收件人的电子邮件地址是有效的。
After the images are downloaded, a Web beacon notification is sent to the sender of the junk email that informs the sender that the recipient email address is valid.
以及地址选择单元，被配置为基于地址选择信号输出rom读取地址和RAM读取地址之一。
The address selecting unit outputs one of the read ROM address and the read RAM address based on the address select signal.
RAM地址生成单元，被配置为基于偏移选择信号而生成与该ROM读取地址对应的RAM读取地址；
The RAM address generating unit generates a read RAM address corresponding to the read ROM address based on the offset select signals.
运用数字式传感器ds18 X 2 0采取单信号传输线进行多点测温的关键技术是传感器的地址编码问题。
It is critical technology to encode the digital sensor DS18X20 that measure multiple temperatures with the 1-wire bus.
运用数字式传感器ds18 X 2 0采取单信号传输线进行多点测温的关键技术是传感器的地址编码问题。
It is critical technology to encode the digital sensor DS18X20 that measure multiple temperatures with the 1-wire bus.
应用推荐