为了用较少的参数反映人肢体皮肤的变形，该文提出以旋转圆锥曲面进行弹性连接体（人体）三维建模。
This paper presents a new method of elastic articulated objects(human bodies) modeling based on a new revolving conic surface.
如果你在圆锥的内侧走的话，那么这样这个曲面就在你的左边了。
Let's say instead that you are walking on the inside of a cone following the boundary. Well, then the surface is to your left.
在每两个摇摆的水平圆形钢平面之间，安装着曲面的圆锥形投影屏幕。
Between each pair of staggered horizontal circular steel plains, the curving, conical projection screens are installed.
圆锥形零件是曲面类零件拉深成形中较为典型的零件之一，对其充液成形的研究具有实际意义。
Since conical part is one of the typical curved parts in sheet metal drawing, research on it has actual significance.
圆锥形零件是曲面类零件中较为典型的零件，对其冲压成形过程的研究是进行曲面类零件研究的基础。
Therefore it is necessary to study forming characteristic of conical part, to analyze various parameters'influence on its forming limit, and to define reasonable blank holding force(BHF).
将曲面与曲面之间的接触原理应用在数控加工中，可解决园柱凸轮，圆锥凸轮等空间凸轮的加工问题。
The contact principle of the surface is applied into the nc machining of the spatial cams, solved the problem of precise machining of the cylinder CAM, and bevel CAM.
介绍了圆锥滚子蜗杆凸轮机构的轮廓曲面方程的建立、压力角和啮合曲面法曲率的计算过程。
This paper describes the establishing process of the equation of working profile curved surface of worm CAM mechanism, the calculation of its pressure Angle and normal curvature.
准双曲面齿轮与普通圆锥齿轮相比，具有重合度大、齿面接触应力低、传动平稳、冲击和噪音小、承载能力高和寿命长等优点。
Compared to bevel gear, hypoid gear has larger overlap coefficient, lower gear contact stress, more smooth transmission, lower impact and noise, higher load bearing capacity, longer life and so on.
利用UG软件的相关功能，生成直齿圆锥齿轮的当量齿轮的齿廓曲线，并沿分度圆锥母线扫描获得齿廓曲面片体；
By using the related method of UG, the profiles of virtual gear are generated, the profile surface is formed by swept along the generater of graduation cone;
现在的主减速器普遍使用准双曲面圆锥齿轮，这主要是因为 主动锥齿轮的偏移允许轿车上传动轴布置得比从动锥齿轮低 一些，而商用车上又允许布置得比从动锥齿轮高一些。
The hypoid gear is in common use today due mainly to the fact that the offset pinion allows the propeller shaft to be set below, (for cars) or above, (for commercial vehicles) the crown wheel center.
将曲面与曲面之间的接触原理应用于数控加工中，解决了圆柱凸轮、圆锥凸轮等空间凸轮的精密加工问题。
The principle of the surfaces contact is applied into the nc machining of spatial cams to solve the problem of precise machining of the cylinder CAM and bevel CAM.
将曲面与曲面之间的接触原理应用于数控加工中，解决了圆柱凸轮、圆锥凸轮等空间凸轮的精密加工问题。
The principle of the surfaces contact is applied into the nc machining of spatial cams to solve the problem of precise machining of the cylinder CAM and bevel CAM.
应用推荐