拖到绘图页上。右击可编辑圆角半径。
右击可编辑圆角半径。
无特殊注明所有的折弯内圆角半径为r0.5。
All the inside radius of the bending is R0.5 except especial declaration.
我们首先要圆滑小方形，它们需要更小的圆角半径，之后我们再处理其他的。
We will first round off the small rectangles, as they need a smaller radius, and then progressively do the others.
新建一层，再画一个圆角矩形宽度一样，但这次要改改圆角半径，10px足矣。
On a new layer, draw another rounded rectangle, this time with 10px corners at the same width as the original.
对于方形孔，当圆角半径为1/14方形孔边长时，对缓和应力集中系数最有利。
It is most advantageous to relaxed SCF when the comer radius equal to 1/14 side length of square hole.
介绍形成小圆角半径的圆孔翻边模具的结构特点，按体积不变的原则，推导了计算公式。
Die structure based on the process of forming small fillet radius is introduced, and deduced the formula according to the principle of volume invariably.
回弹角随凸模圆角半径和凸凹模间隙的增大而增大，随压边力、板料厚度、摩擦系数和材料硬化指数的增大而减小。
The springback Angle increases with the increase of the punch round radius and clearances between the punch and the die while decreases...
对该零件成形工艺进行了优化，研究了不同的压边力、最小模具圆角半径对冲压成形的影响，通过对模拟结果的分析得出了空调前板的最优化成形方案。
The optimization of drawing technique was researched, and the influence of different blank holder force and minimum die fillet radius on stamping forming was studied as well.
首先用圆角长方形工具创建一个高70px圆角半径为10px的图形（注意要画路径图），现在我们不要底部圆角的部分而为它郑家一个更好的角效果。
Make it 70px high and a radius of 10px or more if you wish. Now we have to get rid of the bottom radius and make a perfect corner out of it.
“header”和“content”查看器的背景颜色、圆角半径、边框和透明度都在外部css文件example . css的类选择器中定义(见清单19)。
The background color, corner radius, and border and thickness styles of "header" and "content" viewers are defined in class selectors of the external CSS file: "example.css" (Listing 19).
加入表面和使用圆角边指挥适当的半径大小。
Join the surfaces and use fillet edge command with proper radius size.
在转角处大量采用圆角。圆角内部最小半径为一个壁厚。
Use generous radius at all corners. The inside corner radius should be a minimum of one material thickness.
为了制作出最佳效果，选择滤镜-杂色-中间值，调节半径，直至调出圆角效果，如下图所示。
To finish the effect, choose Filter Noise Median. Adjust the radius setting until you get rounded corners like the image below.
初步确定了花键轴的断裂是疲劳断裂，裂纹源在花键齿根底部过渡圆角曲率半径最小的表面部位。
We have made certain that the reason of the splined spindle rapture is fatigue failure, its crack initiation lies in the minimal knuckle curvature radius surface region of the spline dedendum bottom.
入口为圆角的车道。可指定拐角的半径。
2减速机输入轴处轴肩处未细致考虑过渡圆角的曲率半径和变化曲线使应力集中严重发生疲劳破坏。
2 the curvature radius and the change curve of the transition fillet at the shoulder of the input shaft of the reducer are not carefully considered.
在数控技能大赛中轮廓倒角和倒圆角的宏程序编制方法有两种：刀具中心轨迹编程和刀具半径补偿编程。
It describes the process of filleting contour in programming with the tool center track and tool radius compenstration.
设计橡皮擦，抓住圆角矩形工具，画一个小矩形的边缘半径1px。
To design the eraser, grab the rounded rectangle tool and draw a small rectangle with an edge radius of 1px.
还有应用半径补偿功能结合宏程序来实现任意的内、外轮廓的倒角、倒圆角。
Furthermore, with the function of cutter radius compensation and macro processor to process edge blend and edge chamfer of any outside and inside profile.
选择与15px半径圆角矩形工具，类型更改为“形状图层”。
Select the rounded rectangle tool with a radius of 15px, change the type to "shape layers".
加工孔口倒圆角时，通常可以用成型刀来加工，但是当倒角半径比较特殊时用传统的方法加工就比较困难。
The forming cutter can usually be used to process the orifice chamfering, but when the chamfering radius is special, it is more difficult to use the traditional method to process.
加工孔口倒圆角时，通常可以用成型刀来加工，但是当倒角半径比较特殊时用传统的方法加工就比较困难。
The forming cutter can usually be used to process the orifice chamfering, but when the chamfering radius is special, it is more difficult to use the traditional method to process.
应用推荐