研究了在不同入射波向时每个方墩的群墩影响系数随墩距变化的规律并与折算圆墩的结果进行了比较。
Using Bretschneider spectrum as incident wave spectrum, the grouping coefficients of square caissons are obtained for various incident wave direction and caisson spacing.
从变形能力的不确定方面研究了圆截面钢筋混凝土桥墩曲率极限状态和曲率延性系数。
The curvature limit state and curvature ductility factor of circular reinforced concrete bridge piers are investigated in terms of the uncertainty in deformation capacity.
而特征多项式的系数与有向图的圆族有着密切的关系。
And the coefficients of eigen-polynomial expressions were closely related to the circular sets of a directional graph.
本文阐述了渐开线直齿圆柱齿轮顶圆直径及齿轮模数、变位系数和压力角等参数的确定方法和步骤。
The method and procedure of measuring and calculating involute spur gear geometrical parameters such as tip diameter, module, modification coefficient and pressure Angle were shown in this paper.
确定了非圆齿轮的基本参数：基础圆半径、偏心率、变形距和中心距比例系数。
The basic parameters of non-circular gear are determined, such as primary circle, eccentricity ratio, eccentricity throw and proportional coefficient of center distance.
提出了一种估计均匀圆阵互耦系数的算法。
A new mutual coupling calibration algorithm is presented to estimate the mutual coupling (coefficients) of uniform circular array.
本文用回归分析方法分析了122艘圆舭艇湿表面积系数，得出湿表面积系数预报方程序。
The wetted surface coefficients of 122 round bottom crafts have been analysed in order to derive a prediction equation by the method of least-squares.
激光器件及激光束的动态调制，目标反射系数补偿：采用半导体激光器，经过整形、准直成圆细光束。
Dynamic modulation of laser and laser bean, and offset to target reflection coefficient: laser bean is shaped and collimated to round and slender beam by using of the semiconductor laser.
紊流系数和渗透率与支撑剂粒度、球度、圆度、支撑剂充填层孔隙度和实验条件等有关。
The turbulence coefficient and permeability is re lated with the grain size, sphericity and roughness of the proppant, and the porosity of the proppant-filling bed, and the experimental conditions.
提出了一种利用一个辅助源估计均匀圆阵互耦系数的算法。
This paper presented a mutual coupling calibration algorithm that needs one assistant source for uniform circular array.
建立了采样点均匀分布情况下，圆度误差测量采样点数量与测量极限误差之间的定量关系数学模型。
Under the situation of even distribution of fitting nodes, a mathematic model is established by means of the relation between the number of fitting nodes and the limit error of measurement.
对汽封弹性槽计算的结果表明：将原来设计的单圆弧弹性槽改为三圆弧弹性槽，热应变及热应变集中系数均可明显下降。
Thermal strain and strain concentration factor can also be reduced significantly by changing the single curvature relieve slot into three curvature relieve slot.
对汽封弹性槽计算的结果表明：将原来设计的单圆弧弹性槽改为三圆弧弹性槽，热应变及热应变集中系数均可明显下降。
Thermal strain and strain concentration factor can also be reduced significantly by changing the single curvature relieve slot into three curvature relieve slot.
应用推荐